BEFORE YOU BEGIN

What

is included

 

Q-Scan™ 250 with MSD250 bulb

 

 

or

 

Q-Roll™ 250 with MSD250bulb

 

Removable feet

Power cord with plug

Manual

Warranty Card

Unpacking Instructions

Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition. Notify the shipper immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be returned to the factory, it is important that the fixture be returned in the original factory box and packing.

AC Power

 

To determine the power requirements or particular fixture, see the label affixed to the b ck plate of

 

the fixture or refer to the fixture’s specifications chart. A fixture’s listed current rating is its average

 

current draw under normal conditions. All fixtures must be powered directly off a switched circuit and

 

cannot be run off a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer

 

channel is used solely for a 0% to 100% switch. Before applying power to a Figure 1 - AC Voltage Switch

 

fixture, check that the source voltage matches the fixture’s requirement.

 

Check the fixture or device carefully to make sure that if a voltage selection

 

switch exists that it is set to the correct line voltage you will use.

Warning!

Verify that the power select switch on your unit matches the

 

line voltage applied. All fixtures must be connected to circuits

 

with a suitable Earth Ground.

Safety Instructions

Please read these instructions carefully, which includes important

information about the installation, usage and maintenance?

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet.

Always make sure that you are connecting to the proper voltage and that the line voltage you are connecting to is not higher than that stated on decal or rear panel of the fixture.

This product is intended for indoor use only!

To prevent risk of fire or shock, do not expose fixture to rain or moisture. Make sure there are no flammable materials close to the unit while operating.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent surfaces. Be sure that no ventilation slots are blocked.

Always disconnect from power source before servicing or replacing lamp or fuse and be sure to replace with same lamp source.

Secure fixture to fastening device using a safety chain. Never carry the fixture solely by its head. Use its carrying handles.

Maximum ambient temperature is Ta: 40°. Do not operate fixture at temperatures higher than this.

In the event of serious operating problem, stop using the unit immediately. Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type spare parts.

Don’t connect the device to a dimmer pack.

Make sure power cord is never crimped or damaged.

Never disconnect power cord by pulling or tugging on the cord.

Avoid direct eye exposure to lamp while it is on.

Caution!

There are no user serviceable parts inside the unit. Do not open the housing or

 

attempt any repairs yourself. In the unlikely event your unit may require service,

 

please contact CHAUVET.

Q-Scan 250 & Q-Roll 250 User Manual

3

2005-11-15/13:24

Page 3
Image 3
Chauvet Q-Scan 250 user manual Before YOU Begin, Is included, Unpacking Instructions, AC Power, Safety Instructions

Q-Scan 250 specifications

The Chauvet Q-Scan 250 is a robust and versatile moving head scanner designed to elevate stage performances, events, and installations with its impressive features and cutting-edge technologies. Renowned for its reliability and effectiveness, the Q-Scan 250 has become a favored choice among lighting professionals and enthusiasts alike.

One of the standout characteristics of the Q-Scan 250 is its powerful 250-watt discharge lamp. This high-output lamp delivers vibrant and clear light, ensuring that the projections and patterns are visible even in well-lit environments. The fixture boasts an impressive brightness level, which not only enhances visibility but also enables users to create dynamic and eye-catching displays.

The Q-Scan 250 is equipped with a range of features that promote creativity and flexibility in lighting design. It offers a full 360-degree pan and 180-degree tilt, providing a wide coverage area and allowing for intricate movements that can be easily synchronized with music or other visual elements. This movement capability is enhanced by precision stepper motors that ensure smooth and accurate positioning.

A significant highlight of the Q-Scan 250 is its dual prism system. This feature allows users to create stunning effects by combining multiple beams of light. The rotating prisms can overlay patterns, adding depth and dimension to the projected images. Additionally, the fixture comes with an assortment of gobos that can be easily interchanged, enabling operators to quickly adapt to different themes and styles.

The onboard digital display provides users with an intuitive interface for managing settings and adjusting parameters. This makes it easy to operate the Q-Scan 250 either in standalone mode or through DMX control, offering flexibility for both programmed shows and live performances. The fixture supports multiple DMX channel configurations, allowing for comprehensive control over various functions.

Finally, the Q-Scan 250 is designed with durability in mind, featuring a rugged construction that ensures resilience in various environments. Its efficient heat dissipation system helps maintain optimal performance, extending the lifespan of the lamp and the fixture itself.

In summary, the Chauvet Q-Scan 250 is a feature-rich moving head scanner that combines power, precision, and creativity. With its exceptional brightness, versatile movement, and state-of-the-art technologies, it remains a top choice for lighting designers seeking to create unforgettable visual experiences.