![GENERAL (cont’d.)](/images/new-backgrounds/43665/436653x1.webp)
GENERAL (cont’d.)
D.Riser type construction puts the heat at the bottom inducing natural “stirring action” and evenly distributed temperatures.
E.Units are available with E1 General Purpose, E4 Moisture Resistant, E2 Explosion/Moisture Resistant and E3 Explosion Resistant terminal enclosures.
IMPORTANT: It is the responsibility of the purchaser of the heater to make the ultimate choice of sheath material based upon his knowledge of the chemical composition of the corrosive solution, character of the materials entering the solution, and controls
which he maintains on the process. CHROMALOX cannot warrant any electric immersion heater against failure by sheath corrosion if such failure is the result of operating conditions beyond our control.
Sheath corrosion can result in a ground fault which, depending upon the solution being heated, can cause an explosion or fire.
SPECIFICATIONS
TLC, TLO, TLS, TLI
|
| (10) | |
|
| ||
Sludge Leg/s | Gasket |
| |
Assemble |
| (A) | |
As Shown | |||
(See Installation) |
|
|
| Thermostat Well | Tube Riser |
|
|
|
| |
Heating Elements |
| (A) |
|
|
| (B) | |
|
|
| |
(4) | (B) | Note: Thermostat shipped separately in kit. See page | |
|
| ||
| Tank Bottom | with renewal parts for ordering information. | |
|
| ||
|
|
|
Specifications –
|
|
|
|
|
|
|
|
|
|
| Dimensions (In.) | ||
|
|
|
|
|
|
|
|
|
|
| (A) | (B) | |
| No. |
|
|
|
| No. |
|
|
| Sheath |
| Min. Tank | |
Model | Elements | Phase | Volts | kW | Model | Elements | Phase | Volts | kW | Material | Riser Height | Opening Clearance | |
2 | 1 | 10 | 3 | 1 or 3Δ | 15 | Copper | 48 | 45 | |||||
2 | 1 | 12 | 3 | 1 or 3Δ | 18 | Copper | 48 | ||||||
2 | 1 | 2 | 3 | 1 or 3Δ | 3 | Copper | 36 | ||||||
1 or 3Y | 480 | ||||||||||||
|
|
|
|
|
|
|
|
|
|
| |||
2 | 1 | 4 | 3 | 1 or 3Δ | 6 | Copper | 36 | ||||||
2 | 1 | 6 | 3 | 1 or 3Δ | 9 | Copper | 36 | ||||||
2 | 1 | 8 | 3 | 1 or 3Δ | 12 | Cooper | 36, 48 | ||||||
2 | 1 | 10 | 3 | 1 or 3Δ | 15 | Incoloy | 48 | 45 | |||||
2 | 1 | 12 | 3 | 1 or 3Δ | 18 | Incoloy | 48 | ||||||
2 | 1 | 2 | 3 | 1 or 3Δ | 3 | Incoloy | 36 | ||||||
1 or 3Y | 480 | ||||||||||||
|
|
|
|
|
|
|
|
|
|
| |||
2 | 1 | 4 | 3 | 1 or 3Δ | 6 | Incoloy | 36 | ||||||
2 | 1 | 6 | 3 | 1 or 3Δ | 9 | Incoloy | 36 | ||||||
2 | 1 | 8 | 3 | 1 or 3Δ | 12 | Incoloy | 36, 48 | ||||||
2 | 1 | 2 | 3 | 1 or 3Δ | 3 | Steel | 36 | ||||||
2 | 1 | 3 | 3 | 1 or 3Δ | 4.5 | Steel | 36 | ||||||
2 | 1 | 4 | 3 | 1 or 3Δ | 6 | Steel | 36, 48 | ||||||
2 | 1 | 5 | 3 | 1 or 3Δ | 7.5 | Steel | 48 | 45 | |||||
2 | 1 | 6 | 3 | 1 or 3Δ | 9 | Steel | 48 | ||||||
2 | 1 | 7 | 3 | 1 or 3Δ | 10 | Steel | 48 | ||||||
2 | 1 | 10 | 3 | 1 or 3Δ | 15 | Stainless Steel | 48 | 45 | |||||
2 | 1 | 12 | 3 | 1 or 3Δ | 18 | Stainless Steel | 48 | ||||||
2 | 1 | 2 | 3 | 1 or 3Δ | 3 | Stainless Steel | 36 | ||||||
1 or 3Y | 480 | ||||||||||||
|
|
|
|
|
|
|
|
|
|
| |||
2 | 1 | 4 | 3 | 1 or 3Δ | 6 | Stainless Steel | 36 | ||||||
2 | 1 | 6 | 3 | 1 or 3Δ | 9 | Stainless Steel | 36 | ||||||
2 | 1 | 8 | 3 | 1 or 3Δ | 12 | Stainless Steel | 36, 48 |
2