show Command Examples
Reason (=0 ): no disconnect | has yet occurred |
|
| ||||||
Parameter #1 | Connect Protocol: | ISDN Mode |
|
|
| ||||
Parameter #2 | Compression: | None |
|
|
|
|
|
| |
Parameter #3 | EC Retransmission Count: | 0 |
|
|
| ||||
Parameter #4 | Self Test Error Count: | 0 |
|
|
|
| |||
Parameter #5 | Call Timer: | 37079 secs |
|
|
|
| |||
Parameter #6 | Total Retrains: | 0 |
|
|
|
|
|
| |
Parameter #7 | Sq Value: 7 |
|
|
|
|
|
|
|
|
Parameter #8 | Connected Standard: | V.110 |
|
|
|
| |||
Parameter #9 | TX,RX Bit Rate: | 9600, 9600 |
|
|
| ||||
Parameter #11 | TX,RX Symbol Rate: | 0, 0 |
|
|
|
| |||
Parameter #13 | TX,RX Carrier Frequency: | 0, 0 |
|
| |||||
Parameter #15 | TX,RX Trellis Coding: | (n/a), (n/a) |
|
| |||||
Parameter #16 | TX,RX Preemphasis Index: | 0, 0 |
|
| |||||
Parameter #17 | TX,RX Constellation Shaping: | (n/a), (n/a) | |||||||
Parameter #18 | TX,RX Nonlinear Encoding: | (n/a), (n/a) |
| ||||||
Parameter #19 | TX,RX Precoding: | (n/a), (n/a) |
|
| |||||
Parameter #20 | TX,RX Xmit Level Reduction: | 0, 0 dBm |
| ||||||
Parameter #21 | Signal Noise Ratio: | 0 dB |
|
|
|
| |||
Parameter #22 | Receive Level: | 0 dBm |
|
|
|
|
| ||
Parameter #23 | Frequency Offset: | 0 Hz |
|
|
|
| |||
Parameter #24 | Phase Jitter Frequency: 0 Hz |
|
| ||||||
Parameter #25 | Phase Jitter Level: | 0 degrees |
|
| |||||
Parameter #26 | Far End Echo | Level: | 0 dBm |
|
|
|
| ||
Parameter #27 | Phase Roll: | 0 degrees |
|
|
|
|
| ||
Parameter #28 | Round Trip Delay: | 0 msecs |
|
|
|
| |||
Parameter #30 | Characters transmitted, received: 247, 308 | ||||||||
Parameter #32 | Characters received BAD: | 0 |
|
|
| ||||
Parameter #33 | PPP/SLIP packets transmitted, received: | 9, 9 | |||||||
Parameter #35 | PPP/SLIP packets received (BAD/ABORTED): | 0 | |||||||
Parameter #36 | EC packets transmitted, received OK: | 0, 0 | |||||||
Parameter #38 | EC packets (Received BAD/ABORTED): | 0 |
| ||||||
Parameter #39 | Robbed Bit Signalling | (RBS) pattern: | 0 |
| |||||
Parameter #40 | Digital Pad: | (n/a), | Digital Pad Compensation: None | ||||||
Parameter #41 | V110 frames received bad: | 0 |
|
|
| ||||
Parameter #42 | V110 frames received good: |
| 7417301 |
|
| ||||
Parameter #43 | V110 frames transmitted: | 7417310 |
|
| |||||
Parameter #44 | V110 sync lost: | 0 |
|
|
|
|
|
| |
show modem log
Fields that have been added or changed for this command are:
Connect Protocol: ISDN Mode
Connected Standard V.110
V110 frames received bad:
V110 frames received good:
V110 frames transmitted:
V110 sync lost:
The show modem log command example is as follows:
router# show modem log 1/1
Modem 1/1 Events Log:
...
...
...
4d06h
4d06h
4d06h
Basic V110 for MICA Modems on Cisco Access Servers 7
