5.6 Printing Paper
b) Black mark paper (BM paper)
Also refer to the core dimension and notes of “5.2 Printing Paper” in User’s Manual of standard model. Use print paper shown in the following table or the equivalent.
Paper type | Product name |
Recommended thermal label paper | GG40/P22/G6B from Ojitac, HD75 from Nippon Paper, |
| |
|
|
C
D
A
B
Cut position
E
a) Label paper
A
CB D
Full cut position
| Paper feeding |
E | direction |
|
|
| H |
| I |
|
| ||||
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
| Unit: mm |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Mark | Item | Dimensions |
|
|
|
|
|
|
|
| A | Liner width | 57.5, 59.5, 79.5, |
F
Printable area
Black Mark (printed on the reverse)
Paper feeding
direction
G
Printable area |
F |
G |
J | K |
|
| 82.5 + 0.5 | ||
B | Label width | (Size A) | ||||
|
|
| ||||
|
|
| C | Left edge of label | 2 + 0.5 | |
|
|
| D | Print width | (Size A) - 4 | |
|
|
| E | Top margin | 2 + 1 | |
|
|
| F | Print length | 21 to 296 | |
|
|
| G | Bottom margin | 2 + 1 | |
|
|
| H | Cut position between labels | 1/2 x (Size I) | |
|
| |||||
|
|
| I | Gap between labels | 4 to 30 | |
|
|
| J | Label length | 25 to 300 | |
|
|
| K | Label pitch | I+J | |
|
|
|
| Unit: mm | |
|
|
|
|
| |
Mark | Item |
| Dimensions |
| |
|
|
| |||
BM1 | BM2 | BM3 | |||
|
| ||||
|
|
|
|
| |
A | Right edge of black mark | 13.5 or more | 57.5 or more | 80.5 or more | |
|
|
|
|
| |
B | Left edge of black mark | 15 or or less | 15 oror less | 15 or or less | |
|
|
|
|
| |
C | Black mark height | 5 |
|
| |
|
|
|
|
| |
D | Cut position in black mark | 2.5 |
|
| |
|
|
|
|
| |
E | Top margin | 6.5 |
|
| |
|
|
|
|
| |
F | Black mark pitch | 30 to 300 |
|
| |
|
|
|
|
| |
G | Bottom margin | 9 |
|
| |
|
|
|
|
|
CAUTION!
CAUTION!
Pay attention to the following when using Auto Cutter. Otherwise, a cutter lock or a cutter failure may occur.
■Set the cut length of paper to 25 mm or more.
■When using label paper, cut the gap between labels (liner sheet). Do not cut the label paper (tack paper).
■Adjusting the paper sensor must be carried when the type of liner is changed.
■PCS value of black mark must be 0.9 or more.
■When using the black mark paper, consider the margin of +/- 2 mm for the print position against the standard position and +/- 5 mm for print length.
■Refer to the above drawing for the printable area and have enough margings specified in the marks E and G. If the print data size is out of the printable area, the printer should skip to next page.
Printed in Japan
