Troubleshooting

In general, you should refer any service problems to your Classé dealer. Before contacting your dealer, however, check to see if the problem is listed here.

1.No sound, and no Channel LED is lit.

•The amplifier is not plugged into the AC mains, or the AC mains are down (circuit breaker, fuse).

•A brown-out or short-term loss of power might require the internal microprocessor to be reset. Unplug the unit for at least 30 seconds and then plug it in again and try powering it up.

•The AC mains fuse is blown. See Troubleshooting #4, below (or contact your Classé dealer).

•The AC mains is out of range. Check the voltage specified on the rear panel.

2.No sound, and a Channel LED is blinking red.

•Your protection circuitry may have been engaged. To reset the amplifier, press and hold the Standby button for 3 seconds to power down the amplifier. Then disconnect all inputs and outputs.

•Then try powering up the amplifier by pressing the Standby button. If the LED continues to blink, there is a fault condition in the amplifier itself. It should be powered down, disconnected from the AC mains and taken to your Classe dealer for service.

•If it powers up without any difficulty, power it back down and reconnect only the inputs. Then restart the amplifier. If it goes into its blinking protection mode, something is wrong with a component “upstream” of the amplifier—probably a DC offset or similar problem. Your amplifier is trying to protect your loudspeakers (even small amounts of DC can damage woofers in relatively little time). Try different source components to discover whether the problem is limited to a single source, or exists all the time (which would indicate a problem with the preamplifier). Contact your dealer for help with the appropriate component.

3.The amplifier keeps shutting off.

•Make sure you are providing adequate ventilation to the amplifier, and that the ambient room temperature is below 105°F (40°C).

•Run through the troubleshooting sequence outlined above (assuming the amplifier is going into its protection mode).

ENGLISH

21

Page 20 Page 22
Page 21
Image 21
Classe Audio CA-M400 Troubleshooting, No sound, and no Channel LED is lit, No sound, and a Channel LED is blinking red
Page 20 Page 22

CA-M400 specifications

The Classe Audio CA-M400 is a high-performance power amplifier that encapsulates the essence of quality sound engineering and sophisticated design. Hailing from the renowned Canadian audio manufacturer Classe Audio, this amplifier is designed for audiophiles who demand both power and precision in their audio playback.

One of the standout features of the CA-M400 is its impressive power output. Delivering 400 watts per channel into 8 ohms and 800 watts per channel into 4 ohms, this amplifier is capable of driving a wide range of speakers with ease, ensuring that even the most demanding systems receive ample power. This power is supplemented by Classe's proprietary Current Feedback topology, which allows for high-speed response and minimal distortion, resulting in clear and dynamic sound reproduction.

The CA-M400 employs a dual-mono design, ensuring that each channel operates independently for enhanced imaging and soundstage depth. This configuration not only contributes to the clarity of audio reproduction but also minimizes crosstalk between channels, delivering a more immersive listening experience. The use of high-quality components and a robust power supply further enhances performance, providing exceptional stability and reliability even during peak demands.

Another defining characteristic of the Classe Audio CA-M400 is its system control capabilities. It features a comprehensive range of input options, including balanced XLR and single-ended RCA connections, allowing for flexible integration into various audio setups. Additionally, the amplifier supports remote power control, making it user-friendly and easy to manage within a home theater or stereo system.

Furthermore, the design of the CA-M400 exudes elegance and sophistication. Its sleek chassis is crafted with meticulous attention to detail, featuring a brushed aluminum finish and an intuitive front panel. The amplifier also features a highly efficient thermal management system, ensuring it remains cool during extended listening sessions without compromising performance.

In summary, the Classe Audio CA-M400 is a power amplifier that combines raw power with cutting-edge technology to deliver an unparalleled audio experience. With its formidable power output, innovative design, and exceptional build quality, it stands as a remarkable choice for anyone looking to elevate their audio setup to new heights. Whether it be for critical listening or high-octane movie nights, the CA-M400 promises to deliver an impressive sonic performance that will satisfy even the most discerning audiophiles.
Top Page Image Contents