Manuals / ClearOne comm / Communications / Conference Phone

ClearOne comm XAP 800 operation manual Outputs, Nom

Models: XAP 800

1 149

Download 149 pages 31.96 Kb

Page 52

46	System Configuration ~ Inputs and Outputs

Outputs 1–12

The XAP 800 has 12 line level outputs for sending audio to video codecs, recorders, or amplifiers. To open the Outputs 1–12 configuration window, click the Outputs 1–12 button on the Flow Screen. The Outputs 1–12 button on the Matrix Screen will also open this window.

Figure 3.48. Outputs 1-12 configuration window

These line level outputs are balanced. The nominal output level is 0dBu. The outputs can adjust from -65 to 20dBu.

To select an output channel, click a blank area in the output pane. If you click on the output label, a secondary window will open allowing you to rename the output. The background color for the selected output channel will be light gray. The configurable properties of these outputs are defined in this section.

Mute

Mute mutes the output channel. The light on the button illuminates red when Mute is activated. Default is off (unmuted).

NOM

NOM (constant gain) maintains a constant output level as inputs routed to the output are gated on and off. The XAP 800 reduces the output gain (at the output) for mics based on the number of mics gated on and routed to that output. When using NOM over the expansion bus, only the first four audio channels (O, P, Q, and R)

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Image 52

ClearOne comm XAP 800 operation manual Outputs, Nom

Contents

XAP 800 Audio Conferencing System XAP 800 Installation ClearOne Part No May 2005 Rev Table of Contents System Configuration Advanced ConfigurationOperation ControlTechnical Services Group ~ 1-800-283-5936 USA ~ Introduction Product overviewNew Features Introduction ~ New FeaturesProfessional Services Group Sales and Customer ServiceTechnical Support ClearOne Communications EuMEA GmbHControls and Connections UnpackingFront panel Rear panel Introduction ~ Controls and ConnectionsIntroduction ~ Controls and Connections Networking Expansion busPower Equipment placementOperational Requirements EnvironmentalInstallation Hardware SetupPhoenix connector To connect the unitInstallation ~ Networking Units Networking UnitsExpansion bus connections To create an expansion bus networkMixer mode To select a mixer modeYou can also use G-Ware to select a mixer mode Device IDsInstallation ~ LCD Programming LCD ProgrammingLCD menu tree Pressing Esc at the top of the tree does nothingTo adjust a parameter Select PresetSystem menu Run MacroRS-232 menu Enable Modem Clear PasswordMeter menu Flow Control hardwareDefault Meter Inputs menuOutputs ProcessingOutputs menu GainMeter Reference Point diagram Technical Services Group ~ 1-800-283-5936 USA ~ System Configuration Ware RequirementsInstalling G-Ware To install G-WareCreating Floppy Disk Copies To select AlternateSite Setup Creating a new siteTo create a new site Panel Controls. SeeAdding a XAP To auto-detect unitsTo manually add units Select the XAP 800 icon and click AddConfiguring Unit Properties To configure Unit PropertiesSystem Configuration ~ Site Setup Ware Screens Flow ScreenStatus bar Copying and pasting settingsThat occurred. See page 75 for more information System Configuration ~ G-Ware Screens Matrix ScreenAudio Routing Expansion bus O-Z routingProcess A-H routing Cross point attenuationSystem Configuration ~ Audio Routing Matrix reportInputs and Outputs InputsPeak Meters. The target Pwr Phantom PowerPA Adapt and AEC Reference To create a virtual reference Click Close to exit the windowFilters Non-linear Processing NLPMeters Active FilterType 32. Inputs 1-8 Filters windowTo configure filters Table ViewPA Adaptive Mode GateActivation Chairman OverrideGate Ratio Hold TimeOff Attenuation Ambient Level38. Virtual Reference window Gating Group Select To configure gating group settingsTo assign a gating group Click the Gating Group label to change the group names Min/Max limitsMeters AGC 46. Gain adjust on line level input Outputs NOMOptimizing output gain structure From Expansion Bus O-Z Expansion BusesTo Expansion Bus O-Z Processing Processing A-HCmprs compressor Group54. Processing Filters window Phase BypassAdd Filter Remove FilterDelay Changes you make in the distance and temperature fields57. Process Gain adjust and meter Optimizing process gain structureCreating Presets PresetsOverview Affected when the preset is run Preset Configuration panePreset password is set in the Unit Properties window see Advanced Configuration ~ Presets Cancellation or to change To enable Acoustic EchoWhich outputs To create a preset Storage spaceRunning presets Running multiple presets simultaneouslyTo run a preset using G-Ware To run a preset using front panel controlAssigning a state to a preset command in the Macro Editor Room combining exampleAdvanced Configuration ~ Presets Macros To create a macro using Macro RecorderCreating macros To create a macro using Macro Editor 16 Macro Name windowTo add or insert a command line Editing macrosTo edit a macro To delete a macroTo run a macro using front panel control To run a macro using the Select panel or GpioUse the macro command. See Control for more details Running macrosSignal Generator UtilitiesTo use pink or white noise Select the XAP 800 Unit and Input Channel you want to useTo use tone Document Compare UtilityTo compare site files Operation ~ Utilities Open windowCopying settings Print Preview windowPrint Reports Print Reports windowGFirm Firmware Utility To upgrade firmwareToolbar 13. Selecting baud rate Ware Switcher Before using G-Ware SwitcherTo use G-Ware Switcher Previous versionsCopy and paste settings Message LogMonitoring Views Gate ViewTo configure Meter Views Meter ViewsGpio Builder To program control/status pinsControl/Status a Remote Builder XAP IR RemoteClearOne Control Panels Select IR Remote default from the Select Remote Type listControl ~ Remote Builder To program the XAP IR Remote To program the Volume panel Each Control Panel Button Can Programmed toControl ~ Remote Builder To program the Select panelSerial commands Remote Modem AccessRS-232 Port Command strings To create a command stringTo run a command string Control ~ RS-232 PortTechnical Services Group ~ 1-800-283-5936 USA ~ Appendix a Specifications Maximum # of Mics Mode Noise Cancellation on/off Last Mic Mode Echo Cancellation on/offAmbient Level Filters Appendix B Pinouts RS-232 COM DCE port pinout femaleAppendices ~ Appendix B Pinouts Pin Number ControlControl/Status connectors First 16 pins onPin Definable Type Default Description Control/Status a Port Pinout femalePreset select bit Appendices ~ Appendix B Pinouts Control/Status B port pinoutRS-485 Remote Panel a and B connectors Set connector pinoutLine connector pinout Pin DescriptionAppendix C Control Panel Connecting the Control PanelAppendices ~ Appendix C Control Panel Appendices ~ Appendix C Control Panel Appendix D Accessories Appendices ~ Appendix D AccessoriesAccessory ClearOne Part Number With cableAppendix E Serial Commands Command structureConventions ExampleAppendices ~ Appendix E Serial Commands Groups and channelsType and device IDs Unit typeError number Text message Explanation/Solution Serial command error codesMeter type definitions XAP 800 Serial commands Command FunctionSelects/reports NOM setting on output Selects/reports off attenuation mode forSelects PA adapt mode for specified input Selects/reports phantom power settingAamb Adaptive Ambient Mode AEC Acoustic Echo Canceller Enable/DisableAGC Automatic Gain Control Argument detailsAgcset Automatic Gain Control Adjust Amblvl Ambient Level Adjust100 Name Description UnitsChairo Chairman Override Mode 101Baud Baud Rate Cgroup Compressor Group Select102 Compress Compressor AdjustCompsel Compression Select Decay Decay Adjust Delay Delay AdjustDelaysel Delay Select 103Dfltm Default Meter 104Did Device ID Dspver DSP Version105 Filter Filter AdjustExamples FMP First Mic Priority Mode 106Filtsel Filter Select Flow Flow ControlGain Gain Adjustment 107FPP Front Panel Passcode Button assignmentGHOLD- Gate Hold Time Adjust 108Gate Gate Status ExampleGmode Gating Mode Gratio Gate Ratio Adjust109 Gover Gating Override110 Greport Gate ReportGrpsel Gating Group Select Label LabelLMO Last Mic On Mode Lock Preset and Macro Lock111 LFP Lock Front PanelLockprst Apply the lock to a preset or macro Lockpwd Set preset/macro password112 LVL Level113 Lvlreport Level ReportLvlrrate Level Report Rate = ToggleMaster Expansion Bus Master Mode MAX Maximum Gain Setting114 Macro Macro Execution/ReportingMdmode Modem Mode MIN Minimum Gain SettingCommand form Device Mdmode Value 115116 Minmax Minimum and Maximum Gain SettingMinit Modem Initialization String Mline Mic/Line Adjust Mpass Modem PasswordCommand 117118 Mtrx MatrixNCD Noise Cancellation Depth Ncsel Noise Cancellation Select119 Mute MuteNLP Non-Linear Processing Adjust NOM Number of Open Microphones ModeOffa Off Attenuation Mode 120PAA PA Adaptive Mode PP Phantom PowerPreset Preset Execution/Reporting Command Channel Select mic input Value122 Prgstring Program StringSupported special characters String locationRamp Ramp Gain Adjustment 123Refsel PA/AEC Reference Select Name Description UnitRefset Reference channel setup Sermode Serial ModeTo commands until the new status is matched by the terminal 124Siggen Signal Generator Sftymute Safety mute125 Sigtout Signal Generator Time Out Slvl Speech Level Control Enable/Disable126 String String Execution127 Tout Time Out SelectUID Unit ID VER VersionAppendix F Warranty 128Appendices ~ Appendix F Warranty 129Safety Information 130Appendix G FCC Part 15 Compliance131 Glossary132 Glossary133 134 135 136 137 138 Signal Delay Used for 139Index 14033-35 141 Index142 Frequency responsePhase 143