10272-CPI475_PH2.qxd 7/9/07 11:30 AM Page 14

 

Operation

 

 

 

Troubleshooting Guide

 

 

 

 

 

 

 

 

 

 

 

 

 

Troubleshooting Guide

 

 

 

 

 

Problem/Symptom

Possible Causes

Solution

 

Low output voltage

Overload

Reduce the load.

 

 

No output voltage

Low input voltage

Recharge battery.

 

 

 

 

 

 

 

Check connections

 

 

 

 

 

 

 

and cable.

 

 

No output voltage

Thermal

Allow inverter

 

after prolonged use

shutdown

to cool off.

 

 

 

 

 

 

 

Reduce load,

 

 

 

 

 

 

 

continuous

 

 

 

 

 

 

 

operation input

 

 

 

 

 

 

 

current required.

 

 

 

 

 

 

 

Improve ventilation;

 

 

 

 

 

 

 

Make sure ventilation

 

 

 

 

 

 

 

openings in the

 

 

 

 

 

 

 

inverter are not

 

 

 

 

 

 

 

obstructed.

 

 

 

 

 

 

 

Reduce ambient

 

 

 

 

 

 

 

temperature.

 

 

No output voltage,

High input

Make sure

 

“Protect” indicator

voltage

the inverter is

 

lighted

 

 

 

connected to

 

 

 

 

 

 

 

12V battery.

 

 

 

 

 

 

 

Check regulation

 

 

 

 

 

 

 

of charging system.

 

 

No output voltage

Short circuit

Check load for

 

 

 

 

 

 

 

proper operation.

 

 

 

 

 

 

 

 

No power to

 

 

Blown fuse

Replace fuse.

 

 

inverter

 

 

 

 

 

 

 

Low battery alarm

Poor DC wiring

Check

 

on all the time

 

 

 

connections.

 

 

 

 

 

 

Poor battery

Make sure battery

 

 

 

 

 

 

condition

is fully charged.

 

Operation

 

 

 

Specifications

 

 

 

 

 

 

 

 

 

 

 

 

Specifications

 

 

 

 

Continuous output power (1 hour) .

. . . . . . . . . . . 400W

 

Surge rating (0.1 second)

. . . . . . . . . . . 800W

 

Peak efficiency (12V – 1⁄2 load) . . . .

. . . . . . . . . . > 88%

 

 

Efficiency (full load, 12V)

. . . . . . . . . . > 83%

 

 

No load current draw

. . . . < 0.5A (12.6V)

 

Output waveform (resistive load) . . .

Modified sine wave

 

Output frequency

. . . . . 58HZ – 62HZ

 

Output voltage

 

. . . . . . . . . . . . . . . . .

. . . . . 109V – 120V

 

USB output

. . . . . . . . . . . . . 5V

 

Input voltage . .

. . . . . . . . . . . . . . . .

10.4VDC – 14.4VDC

 

Alarm voltage (unload)

. . . . .10.2V – 10.8V

 

Shutdown voltage (unload)

. . . . . . 9.2V – 9.8V

 

Operating temperature range

. . . . . . . 0°C – 40°C

 

 

 

 

 

 

(32°F – 104°F)

 

Storage temperature range

. . . . . -40°C – 85°C

 

 

 

 

 

 

(-40°F – 185°F)

 

Protection . . . .

. . . . . .Overload, short-circuit, overtemp,

 

Notes

 

reverse polarity, under/over voltage

 

 

 

 

 

All protection is automatically recovered.

To protect the battery, if the unit needs to be restarted after low voltage protection, the voltage of DC input should be above 12V.

To extend the life of the fan, it will stop when there is no load. The speed of the fan increases as the load increases.

The unit is completely insulated in input and output for added safety.

14

Nothing Comes Close to a Cobra® 15

 

 

Page 10
Image 10
Cobra Electronics CPI 475 owner manual Troubleshooting Guide, Specifications, Solution