DETAILED INSTALLATION | 4 |
I. Source-Output, Power Connections and Controls
The connectors and controls are clearly marked on the back panel of the AMPLIFIER v10. Note the correct channel orientation. The function and channel markings on the rear panel correspond to the front panel controls and their signal paths.
1.The MODE switch selects between unbridged or bridged operation. The default position is UNBRIDGED. For information on bridging see BRIDGE SETUP.
2.The UNBALANCED and BALANCED inputs should be attached to the appropriate unbalanced and balanced outputs of a preamplifier either directly or through a crossover or processor, as appropriate to the application.
3.The CH1 OUTPUT, CH 2 OUTPUT, CH 3 OUTPUT, CH 4 OUTPUT should be attached to four or three or two speakers. This will depend on how many channels are bridged.
NOTE: THERE ARE NO OUTPUT FUSES SO AS TO INSURE A LOW OUTPUT IMPEDANCE. SPEAKER PROTECTION IS LEFT TO THE SPEAKER MANUFACTER AS THEY WOULD BEST KNOW HOW TO PROTECT THEIR SPEAKER.
4.The MAIN POWER switch, once all appropriate connectsions are made, may be left on as the AMPLIFIER v10 draws a negligible amount of current when the BIAS is turned off.
5.The FUSE AND VOLTAGE SELECTOR houses a 5 X 20 slow blow fuse and voltage selector cartridge. Should the fuse blow, contact a Coda dealer or call Coda directly. When changing the fuse, or altering the voltage selection be sure this unit is disconected from its AC power source.
6.The AC LINE INPUT should be attached to the power cable provided with the amplifier. After making the appropriate connections insert the three prong safety plug into an appropriate AC power source. Once the AMPLIFIER v10 is properly connected, the power switch may be turned on and the led on the front panel will light indicating a ready state.
3 | 3 | 2 | 1 | 2 | 2 | 1 | 2 | 3 | 3 |
CH 1 OUTPUT |
|
|
| CH 2 OUTPUT |
BRIDGED
INPUT
FOR CONTINUED PROTECTION
AGAINST SHOCK OR FIRE:
1.REPLACE FUSE WITH SAME TYPE AND RATING
2.DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE
!AC LINE FUSE CHART
VOLTAGE |
| FUSE TYPE | |
100V | 8 AMP | SLOW BLOW 5 x 20mm | |
120V | 8 AMP | SLOW BLOW 5 x 20mm | |
220V | 4 AMP | SLOW BLOW 5 x 20mm | |
240V | 4 AMP | SLOW BLOW 5 x 20mm | |
|
|
|
|
|
|
|
|
CH 1 INPUTS | CH 2 INPUTS | CH 3 INPUTS |
| CH 4 INPUTS | CH 3 OUTPUT | CH 4 OUTPUT | |
UNBALANCED |
|
|
| UNBALANCED |
|
|
|
|
|
|
|
|
| BRIDGED |
|
|
|
|
|
|
| INPUT |
|
BALANCED |
|
|
| BALANCED |
|
|
|
UNBRIDGED |
|
|
| UNBRIDGED |
|
|
|
|
|
|
|
|
| ||
AND CHANNEL 2 |
|
|
| AND CHANNEL 4 |
| ||
|
|
|
|
|
| ||
|
| MODEL |
|
|
| CAUTION | ! |
|
| SERIAL NUMBER |
|
|
| WARNING | |
|
| VOLTAGE REQUIREMENT |
| HZ | TO PREVENT ELECTRIC SHOCK, DO NOT | ||
|
| POWER REQUIREMENT |
| VA | |||
|
|
| REMOVE COVER. NO USER SERVICEABLE | ||||
|
|
| MANUFACTURED IN THE USA |
| PARTS INSIDE. REFER SERVICING TO | ||
|
|
|
|
|
| QUALIFIED SERVICE PERSONNEL. | |
~ AC LINE INPUT | FUSE AND VOLTAGE SELECTOR | MAIN POWER | NOTE | ! | |||
|
|
|
|
|
| DO NOT ALLOW AMPLIFIER OUTPUTS | |
|
|
|
|
|
| TO COMMON BETWEEN CHANNELS, | |
|
|
|
|
|
| OR CONTACT CHASSIS OR INPUT | |
|
| 120 |
|
|
| GROUNDS, OR TO BE CONNECTED | |
|
|
|
|
|
| ||
|
|
|
|
|
| TO ANY ACTIVE CURRENT SOURCE. | |
|
|
|
|
|
| THIS PRODUCT | |
|
|
|
|
|
| IS DESIGNED, | |
SEE SERIAL TAG FOR POWER |
| FUSE VALUE | OFF | ON | ENGINEERED | ||
REQUIREMENTS, REMOVE POWER | VOLTAGE SELECTION- |
|
| AND BUILT IN THE UNITED | |||
CORD BEFORE CHANGING |
| SEE OPERATION MANUAL |
|
| STATES OF AMERICA. |
| |
FUSE OR LINE VOLTAGE |
|
|
|
|
|
|
6 5 4