Boulder, Colorado
Installation Guide
MicroRouter 2250R
Compatible Systems Corporation 4730 Walnut Street Suite
MicroRouter 2250R Installation Guide, Version
Copyright 1999, Compatible Systems Corporation
Part number A00-1268
Chapter 4 - CompatiView Software Installation
Chapter 3 - Network Installation
Chapter 1 - Introduction
Chapter 2 - Getting Started
WAN INTERFACE CONFIGURATION
Chapter 5 - Command Line Management
Chapter 6 - Basic Configuration Guide
ETHERNET INTERFACE CONFIGURATION
Appendix A - Shipping Defaults
Appendix C - LED Patterns and Test Switch Settings
Systems
Appendix E - Terms and Conditions
Appendix B - Connector and Cable Pin Outs
A Note About On-Demand Internetworking
Chapter 1 - Introduction
About the MicroRouter 2250R
A Note About Firewalls
Chapter 1 - Introduction
MicroRouter 2250R Installation Overview
Chapter 6 - Basic Configuration Guide
Chapter 3 - Network Installation
Chapter 4 - CompatiView Software Installation
Chapter 5 - Command Line Preparation
Page
Chapter 2 - Getting Started
Chapter 2 - Getting Started
A Few Notes
Warranty and Service
CompatiView Management Software Reference Guide
What You Will Need To Get Started
Needed For Installation
Supplied with the MicroRouter 2250R
Chapter 2 - Getting Started
Ethernet Connection Requirements
T1 Line Connection Requirements
Other Telco Line Connection Requirements
Chapter 2 - Getting Started
The MicroRouter 2250R secondary port is an RS-232 sync/async inter- face. The RS-232 interface is capable of communicating to another router or a PPP client machine over a modem, 56K CSU/DSU, or ISDN Terminal Adapter
RS-232 Interface
Chapter 3 - Network Installation
Placing the Router
Chapter 3 - Network Installation
Connecting to Twisted-Pair Ethernet
Connecting the Router to the Ethernet
Connecting the Router to a T1 Line
Connecting a Line Device to the Secondary Port
Connecting an Out-of-Band Management Console
Powering Up the Router
Chapter 3 - Network Installation
Page
Chapter 4 - CompatiView Software Installation
Installation and Operation
CompatiView for Windows
System Requirements
Chapter 4 - CompatiView Software Installation
Transport Protocols and CompatiView
Out-of-Band Command Line Management
Chapter 5 - Command Line Management
Setting Up Telnet Operation
Temporarily Reconfiguring a Host for Command Line Management
Ethernet 0 section
Page
Chapter 6 - Basic Configuration Guide
Ethernet Interface Configuration
Chapter 6 - Basic Configuration Guide
Suggested for IP
IP Protocol
IPX Protocol
Required for IP
Suggested for IPX
AppleTalk Protocol
DECnet Protocol
Chapter 6 - Basic Configuration Guide
Chapter 6 - Basic Configuration Guide
WAN Interface Configuration
Internal T1 CSU/DSU WAN 0 Physical Communications Settings
RS-232 WAN 1 Physical Communications Settings
Chapter 6 - Basic Configuration Guide
PPP Configuration
Internal T1 CSU/DSU WAN 0 Link Configuration
RS-232 WAN 1 Link Configuration
Required for IP
Chapter 6 - Basic Configuration Guide
IP Protocol
Suggested for Dial-On-Demand Operation
Required for IPX
Chapter 6 - Basic Configuration Guide
IPX Protocol
AppleTalk Protocol
Suggested for DECnet
Chapter 6 - Basic Configuration Guide
DECnet Protocol
Required for DECnet
RS-232 WAN 1 Link Configuration
Frame Relay Configuration
Frame Relay DLCI Mappings
Internal T1 CSU/DSU WAN 0 Link Configuration
IP numbered interface IP address IP subnet mask IP broadcast address
Chapter 6 - Basic Configuration Guide
IP Protocol
Required for IP Numbered Interface
Suggested for IP
Chapter 6 - Basic Configuration Guide
IPX Protocol
Required for IP Unnumbered Interface
Suggested for AppleTalk
AppleTalk Protocol
DECnet Protocol
Required for AppleTalk
Internal T1 CSU/DSU WAN 0 Link Configuration
Saving a Configuration File to Flash ROM
WAN 0 SMDS Configuration
SMDS Addressing
Page
Appendix A - Shipping Defaults
Appendix A - Shipping Defaults
Default Password
Ethernet Interface
AppleTalk Defaults
WAN Interfaces
IP Defaults
IPX Defaults
Pin Outs for T1 Female Connector DTE
Pin Outs for DB-25 Male to DB-25 Female RS-232 Data & Console Cable
Appendix B - Connector and Cable Pin Outs
Page
Ethernet Traffic Indicators Ethernet LED Bar
MicroRouter 2250R LED Patterns
Appendix C - LED Patterns and Test Switch Settings
Power On, No Traffic
Run Boot ROM Downloader
MicroRouter 2250R Switch Settings
38 Appendix C - LED Patterns and Test Switch Settings
Other Indicators on All LED Bars
Appendix D - Downloading Software From Compatible Systems
Page
Appendix E - Terms and Conditions
Appendix E - Terms and Conditions
Appendix E - Terms and Conditions
To obtain service under this Warranty, the Customer or subsequent pur- chaser, if applicable must follow the procedures outlined below, under “Product Return Policy.”
Appendix E - Terms and Conditions
ber of each item being returned c original Compatible Systems Sales Agreement number and d any special instructions. Upon receipt of this information, Compatible Systems will issue an RMA “Return Material Authorization” number and any required U.S. Customs identification to assure correct identification of the Customer and to insure prompt and accu- rate processing