Cooper Lighting HR117C, HR12117C Electrical Ratings, HR87C SLC, Photometrics, Technical Data

ELECTRICAL RATINGS CHICAGO HR SERIES

	Rated Wattage to 87 1/2% of Rated D.C. Voltage
Model	Type	DC Voltage 1 1/2 Hours			Lamp Watts	Remote Watts
HR87C	SLC	6		87	24	63
HR117C	SLC	6		117	24	93
HR12117C	SLC	12		117	24	93
HR180C	SLC	6		180	24	156
HR12170C	SLC	12		170	24	146
HR12210C	SLC	12		210	24	186
HR12360C	SLC	12		360	24	336
*Batteries may be shipped separately.			SLC=Sealed Lead Calcium

PHOTOMETRICS

Lamp Information

Type	Wattage	Number	Figure
Halogen	12	29-66	1
Halogen	12	29-66	1
Halogen	12	29-45	1
Halogen	12	29-66	2
Halogen	12	29-45	2
Halogen	12	29-45	2
Halogen	12	29-45	2

H o r i z o n t a l D i s t r i b u t i o n

15
FEET
LEFT		1FC	0.5	0.3	0.2	0.1 LAMP
0
						AXIS
FEET
RIGHT
150	20	30	40		50	60

FEET FROM LAMP (Measured on axis)

Lamp No. 29-45 and 29-66

Initial Lumens – 302

Ve r t i c a l D i s t r i b u t i o n

15
FEET
LEFT		1FC	0.5	0.3	0.2	0.1 LAMP
0
						AXIS
FEET
RIGHT
150	20	30	40	50		60

FEET FROM LAMP (Measured on axis)

Lamp No. 29-45 and 29-66

TECHNICAL DATA

Heads

All metal formed aluminum lampheads. The die cast metal three dimensional swivel assembly permits approximate aiming adjustment from 80° vertical and 358° rotation. The placement is secured with a lockable pivot mounted on a rotating base ring.

Lamps

Designed specifically for emergency lighting applications, the PAR 36 sealed beam type design insures optimum glare- free light distribution along with horizontal and vertical adjustment by rotating the lens within the housing. Tungsten halogen lamps maximize light output with lower wattage.

Housing

The rugged 18-gauge die- formed steel housing is finished with an attractive white corrosion-resistant polyester powder coat paint. Cabinet has keyhole mounting slots, universal mounting pattern, and knockouts in rear and side for AC/DC wiring connections and accessory cord set. Up to three lighting heads can be mounted on the cabinet.

Line - Latched

Sure-Lites’ line-latched electronic circuitry makes installation easy and economical. A labor efficient AC-activated load switch prevents the lamps from turning on during installation to

a non-energized AC circuit. Line-latching eliminates the need for a contractor’s return to a job site to connect the batteries when the building’s main power is permanently turned on.

Solid - State Charger

Supplied with a 120/277 VAC, voltage regulated solid-state charger. Immediately upon restoration of AC current after a power failure, the charger provides a high charge rate. The charge circuit reacts to the condition of the battery and alters the rate of charge in order to maintain peak battery capacity and maximize battery life. Solid-state construction recharges the battery following a power failure in accordance with UL 924.

Overload and Shor t

Circuit Protectio n

The solid-state overload monitoring device in the DC circuit disconnects the lamp load from the battery should excessive wattage demands be made and automatically resets when the overload or short circuit is removed. This overload current protective feature eliminates the need for fuses or circuit breakers for the DC load.

Brownout Circuit

The brownout circuit in Sure- Lites’ units monitors the flow of AC current to the unit and activates the emergency lighting system when a predetermined reduction

of AC power occurs. This

dip in voltage will cause most ballasted fixtures to extinguish causing loss of normal lighting even though a total power failure has not occurred.

Solid - State Transfer

The unit incorporates a solid- state switching transistor which eliminates corroded and pitted contacts or mechanical failures associated with relays. The switching circuit is designed to detect a loss of AC voltage and automatically energizes the lamps. Upon restoration of the AC power, the emergency lamps will switch off and the charger will automatically recharge the battery.

Low - Voltage Disconnect

When the battery’s terminal voltage falls below 80% of the rated voltage, the low-voltage circuitry disconnects the lighting load. The disconnect remains in effect until normal utility power is restored, preventing deep battery discharge.

Test Switch/Power Indicator Ligh t

Conveniently located Test Switch allows for manual verification of proper operation of the transfer circuit and emergency lamps. The Power Indicator Light provides visual assurance that the AC power is on.

Sealed Lead Calcium Battery

The fully sealed, long-life, maintenance-free lead calcium battery is ideal for emergency lighting applications. These recombinant cycle batteries typically provide eight to ten years of life and may be operated in any position.

Warranty

All Sure-Lites’ units are backed by a firm one-year warranty against defect in material and workmanship (excluding lamps). Maintenance free, long-life, sealed lead calcium batteries carry a five-year pro-rata warranty.

Specifications and Dimensions subject to change without notice.	ADX041293
Sure-Lites • Customer First Center • 1121 Highway 74 South • Peachtree City, GA 30269 • TEL 770.486.4800 • FAX 770.486.4801	03/21/2007 11:33:08 AM