Instruction Manual: COSTAR® 12SIR, 12V System CO Alarm

NOTE: Manufacturer strongly recommends replacement of alarm six years after date of purchase. Under no circumstances should the alarm be used (7) years after the date of purchase.

6.0DEVELOPING YOUR OWN CO SAFETY PLAN

This CO alarm can quickly alert you to the presence of CO — it cannot prevent toxic CO emissions. Please note that there are hazards against which CO detection may not be effective, such as gas leaks or explosions. The ultimate responsibility for protection against toxic CO gas rests solely on you.

Installing CO alarms is just the first step in protecting your family from toxic CO poisoning. We also suggest that you create an effective, comprehensive safety program as outlined below.

6.1Install CO alarms properly following the instructions in this manual.

6.2Develop a family escape plan and practice it with your entire family, especially small children.

–Draw a floor plan of your home/ residence and find two ways to exit from each room. There should be one way to get out of each bedroom without opening the door.

–Make sure that all occupants know what the CO alarm signal means and how they must be prepared to leave the residence by themselves if necessary.

–Decide on a meeting place a safe distance from your house and make sure all occupants understand where they should go and wait if there is a dangerous CO condition.

–Conduct CO safety drills at least every 6 months to make sure that everyone, even small children, know what to do in order to escape safely.

–Know where to go to call the Fire Department from outside your residence.

This unit is designed to detect carbon monoxide (CO) entering its sensing chamber. It does not sense combustible gas (such as natural gas, propane or butane), heat, smoke or flames.

When properly located, installed, and maintained, this CO alarm is designed to provide early warning of developing poisonous CO conditions at a reasonable cost.

This alarm monitors the air, and when it senses CO, it activates its built-in alarm. It can provide precious time for you and your family to escape from your residence before CO can seriously injure or kill. However, such an early warning is possible only if the alarm is located, installed, and maintained as specified in the Owner's Manual.

7.0IMPORTANT: WHAT YOUR CO ALARM CAN AND CANNOT DO

If bedroom doors are usually closed at night, alarms should be placed in each bedroom as well as in the common hallway between them. CO alarms may not sense CO on a different level of a residence or building. For example, a second floor alarm may not sense a CO leak on the first floor or in the basement.

Therefore, alarms should be placed on every level of a residence or building. If the alarm is located outside of a bedroom, it may not wake up a sound sleeper, especially if the bedroom door is closed or only partly open. If the alarm is located on a different level of the residence than the bedrooms, it is even less likely to wake up people sleeping in the bedroom. Installing CO alarms may qualify you for lower homeowner's insurance rates, but CO alarms are not a substitute for insurance. Homeowners and renters should continue to insure their lives and property.

WARNING: The COSTAR® Model 12SIR CO Alarm is not designed for marine, RV, or aeronautical use.

NOTE: This unit contains no batteries and will not operate without power.

8.0INSTALLING THE COSTAR® 12SIR FOR RESIDENTIAL USE

8.1RECOMMENDATIONS

One of the most important considerations in any CO alarm system is the location of the alarms. Statistics of the National Fire Protection Association (NFPA) show that most of the fatal CO occurrences happen at night while people are sleeping. Early warning of CO is best achieved by the correct installation of CO alarms. Placement of an alarm in a garage may cause an alarm due to CO from automotive exhaust.

8.2RECOMMENDED MOUNTING LOCATIONS

Put a CO alarm inside each bedroom where the occupant closes the door while sleeping. A closed door can block particulate smoke, but CO gas is likely to get through.

QGI P/N 099-0066-01 REV 10/26/01 Page 3 of 7

Page 2 Page 4
Page 3
Image 3
Costar 12SIR Developing Your OWN CO Safety Plan, Important What Your CO Alarm can and Cannot do, Recommendations
Page 2 Page 4

12SIR specifications

The Costar 12SIR is a cutting-edge, high-performance infrared (IR) camera designed specifically for industrial applications, scientific research, and advanced surveillance. Known for its robust features, advanced technologies, and exceptional imaging characteristics, the 12SIR has gained recognition as a versatile tool for professionals across various fields.

One of the standout features of the Costar 12SIR is its sensitivity and resolution. This camera boasts a high-resolution sensor capable of capturing images at a resolution of 1280x1024 pixels. This sharp resolution allows users to capture detailed thermal images, which can be critical for applications requiring precision, such as electrical inspections, mechanical evaluations, and building diagnostics.

Equipped with cutting-edge infrared technology, the Costar 12SIR operates in the infrared spectrum, enabling it to detect heat emissions from surfaces. Its thermal sensitivity, often referred to as NETD (Noise Equivalent Temperature Difference), is impressively low, making it capable of identifying even slight temperature variations. This sensitivity is crucial for detecting potential issues in industrial systems or providing insight into thermal management in scientific research.

The camera's imaging capabilities are further enhanced by its advanced optics. The Costar 12SIR features a variety of interchangeable lenses, providing flexibility for users to select the appropriate lens for their specific application requirements. This adaptability allows for viewing objects at various distances and makes the camera suitable for both close-up inspections and long-range surveillance.

Moreover, the Costar 12SIR is equipped with an intuitive user interface, which simplifies operation. Its user-friendly controls enable quick adjustments to settings such as contrast, brightness, and color palettes, ensuring the optimal visualization of thermal data. This ease of use is complemented by comprehensive software that supports data analysis, reporting, and integration with diverse imaging systems.

In addition, the Costar 12SIR is built with durability in mind. It features a rugged design that withstands harsh environments, making it reliable in industrial settings. Its portability allows for easy deployment across various job sites, ensuring that professionals can carry out inspections and monitor systems with minimal hassle.

Overall, the Costar 12SIR stands out as a leading thermal imaging solution that combines high performance, versatility, and reliability. With its advanced capabilities and robust design, it proves to be an essential tool for anyone in need of precise thermal analysis and reliable imaging solutions. Whether in the field of maintenance, engineering, or research, the Costar 12SIR is poised to enhance productivity and improve decision-making through accurate thermal analysis.
Top Page Image Contents