Miter SAW Parts List | Craftsman 137.21214 guide

PARTS

10” MITER SAW PARTS LIST

MODEL: 137.212140

When servicing use only CRAFTSMAN replacement parts. Use of any other parts may create a HAZARD or cause product damage.

Any attempt to repair or replace electrical parts on this miter saw may create a HAZARD unless repair is done by a qualified service technician. Repair service is available at your nearest Sears Service Center.

Always order by I.D. Number

PARTS LIST FOR SCHEMATIC A

I.D.NO	Description	Size	Qty.	I.D.NO Description		Size	Qty.
0812	SPRING PLATE		1	0K24	HEX.SOCKET HD.CAP BOLT	M8*1.25-35	2
0818	MITER HANDLE		1	0K2N	HEX.SOCKET HD.CAP BOLT	M8*1.25-25	1
081A	PLASTIC SLEEVE		1	0K2S	HEX.SOCKET HD.CAP BOLT	M8*1.25-20	3
081D	NEEDLE POINTER		1	0K3J	CR.RE.PAN HD.TAPPING SCREW	M4*0.7-16	3
081G	FOLLOWER PLATE		5	0K56	CR.RE.COUNT HD.SCREW	M5*0.8-12	1
081J	TABLE INSERT		1	0K5C	CR.RE.COUNT HD.SCREW	M6*1.0-16	1
081K	MITER SCALE		1	0K7Z CR.RE.TRUSS HD.ROUND NECK SCREW		M6*1.0-14	2
081U	SUPPORT		1	0K9X	DRIVE SCREW	Φ2.3-5	2
0821	BEVEL SCALE		1	0KBD	CR.RE.PAN HD.TAPPING SCREW	M4*18-25	6
0824	PIVOT SHAFT		1	0KCX	CR.RE.PAN SCREW	M5*0.8-10	5
0826	NEEDLE POINTER		1	0KD7	CR.RE.PAN HD.TAPPING SCREW	M4*0.7-10	4
0828	ROTATION SLIDE PLATE		1	0KDM	CR.RE.PAN HD.SCREW	M5*0.8-20	2
0829	ANGLE REGULATOR		1	0KDN	CR.RE.PAN HD.SCREW	M5*0.8-25	1
0831	SHAFT SLEEVE		1	0KDR	CR.RE.PAN HD.SCREW	M5*0.8-10	2
083R	TRIGGER		1	0KDT	CR.RE.PAN HD.SCREW	M6*1.0-8	2
083Y	COMPRESSION SPRING		1	0KE0	CR.RE.PAN HD.SCREW	M6*1.0-40	2
083Z	CORD CLAMP		1	0KMS	HEX.NUT	M6*1.0 T=5	1
084W	LABEL		1	0KQX	HEX.NUT	M6*1.0 T=6	1
0BAG	BLADE		1	0KQX	LOCK NUT	M6*1.0 T=6	1
0CES	COMPRESSION SPRING		1	0KQZ	LOCK NUT	M10*1.5 T=10	1
0CKS	WIRE SPRING		1	0KR0	LOCK NUT	M12*1.75 T=12	1
0CM2	SAFETY CLAMP		1	0KUX	TERMTNAL		1
0CQH	BEVEL LOCK HANDLE ASS'Y		1	0LU2	LIMIT SWITCH		1
0CV5	DUST BAG ASS'Y		1	0QQ1	GUARD-CORD		1
0D7W	LOCKING LATCH		1	0S1N	ARM-MITER		1
0D7X	SHAFT		1	0S1P	TABLE		1
0D7Z	LOCKING LATCH KNOB		1	0S1S	COLLAR		1
0D87	TORSION SPRING		1	0S1T	HOUSING ASSEMBLY		1
0D99	SHIM		1	0S2B	CR.RE.PAN HD.TAPPING SCREW	M6*1.0-25	2
0D9B	ANCHOR BLOCK		1	0STZ	LABEL		1
0D9R	CAUTION LABEL		1	0V8C	POWER CABLE		1
0D9S	CHIP PLATE		1	0V8M	FENCE		1
0D9T	RUBBER PAD		1	0V9J	MOTOR		1
0DHT	SPRING		1	0XK9	BUTTON SWITCH		1
0DTZ	ARBOR COLLAR		1	0XKA	SEGMENT HADELE		1
0DVJ	BLADE WRENCH		1	0XQ5	HANDLE COVER		1
0DWU	STOP BLOCK		1	0XQ6	HANDLE		1
0DWW	EXTENTION WING		2	20Z0	LEVER		1
0J4J	FLAT WASHER	Φ10*20-2	1	21K2	BASE		1
0J4R	FLAT WASHER	Φ10*20-3	1	21K3	WING BOLT	M6*1.0-20	1
0J7R	FLAT WASHER	1/2*1-3/64	1	23E0	BRACING PLATE		1
0JMM	O-RING		1	25NZ	ARBOR LASER ASS'Y		1
0JPE	HEX.HD.BOLT	M6*1.0-20	1	25Q5	PC-GUARD		1
0JQT	HEX.HD.BOLT	M10*1.5-75	1	26Q0	TRADE-MARK LABEL		1
0JUK	HEX.SOC.HD.CAP BOLT	M6*1.0-16	1	26WS	MOTOR LABEL		1
0JVY	HEX.SOC.HD.CAP BOLT	M6*1.0-16	2	279L	WARNING LABEL		1
0JZD	HEX.SOC.SET SCREW	M5*0.8-10	1
0JZF	HEX.SOC.SET SCREW	M6*1.0-10	2
0JZN	HEX WASHER HD BOLT	M8*1.25-20	1
0K0W	HEX.HD.SCREW AND WASHER	M6*1.0-25	2
				26RV	INSTRUCTION MANUAL		1

24

Image 24

Craftsman 137.21214 operating instructions Miter SAW Parts List, Parts List for Schematic a

Contents

With Laser Trac Part No.137212140001 Table of Contents Power Tool Safety General Safety Instructions Compound Miter SAW Safety Specific Safety Instructions for this Compound Miter SAWPower Supply and Motor Specifications Electrical Requirements Electrical Requirements and Safety Motor Safety ProtectionDouble Insulated Guidelines for Extension Cords Accessories and Attachments Tools Needed for Assembly Recommended AccessoriesAccessories Carton Contents Know Your Compound Miter SAW Glossary of Terms Woodworking Terms Assembly and Adjustments Installing Extension Wings FIG. E Installing the Stop Block FIG. EInstalling the Extension Wings FIG. E Removing or Installating the Blade Installing the HOLD-DOWN Clamp FIG. H-1 Installing Blade Fig. F, G, HMiter Scale FIG. J To Adjust Miter Angles Cutting arm pivot adjustment90o Bevel Pointer Adjustment Fig. N Cutting ARM Travel FIG. K Fig. N Safety Instructions for Basic SAW Operations Operation Dress for Safety When SAW is RunningPlan Your Work Inspect Your Workpiece Body and Hand Position FIG. P Turning the SAW on Fig. QLaser -TRAC Operation of Laser Miter CUT FIG. R Bevel CUT FIG. SCompound CUT FIG. T Cutting Bowed Material FIG. U Workpiece Support FIG Auxilary Wood Fence FIG. W Cutting a Dimensional 4X4 with ONE CUT Fig Vertical Miter Cutting FIG. YCutting Base Molding FIG. Z Bevel/Miter Settings Changing the Laser BatteriesCutting Crown Molding FIG. AA, BB Changing the Batteries Fig. CC Maintenance Troubleshooting Guide Troubleshooting Guide MotorTroubleshooting Guide SAW Operation Problem Problem Cause Suggested Corrective Action Miter SAW Parts List Parts List for Schematic aParts Schematic a Compound Miter SAW Parts List for Schematic B Motor Description Size QTY Schematic B Motor Get it fixed, at your home or ours