Craftsman 137.2191 owner manual ADJ UST V Entinstructions, Fig, K

_NSTALMNG FEED HANDLES (FIG. H)

1.Locate three feed handles in the loose parts bag.

2.Screw the feed handles (1) into the threaded holes (2) in the hub (3). Tighten.

,Using a rubber maltet, plastic-tipped hammer, or a block of wood and a hammer, firmly tap the chuck upward into position on the spindle shaft.

Fig, K

FENCE ASSEMBLY (F_G°M}

t.Determine the desired location for the fence (.1).

2.Aiign the mounting holes of the fence over the table top slots.

3.Place a washer (2) on the threaded end of the knob (3).

Insert the knob through the mounting hole of the fence and the table slot.

4.Place a washer and wing nut (4) on the knob from ' under the table.

5.Repeat for the other knob and tighten.

ADJ UST 'V ENTINSTRUCTIONS

CAUTION: All the adjustments for the operation of the drill press have been completed at the factory. Due to normal wear and use, some occasional readjustments may be necessary.

To avoid injury from an accidental start, ALWAYS make sure the switch is in the "OFF" position, the switch key is removed, and the plug is not connected to the power source outlet before making belt adjustments.

INSTALLING THE CHUCK (FIG. t, J and K)

t.Clean out the tapered hote in the chuck (1) with a clean cloth.

2.Clean tapered surfaces on the spindle (2).

CAUTION: Make sure there are no foreign particles sticking to the surfaces. The slightest piece of dirt on any of these surfaces will prevent the chuck from seating properly. This will cause the drill chuck and bit to wobble. If tapered hole is extremely dirty, use a cleaning solvent.

Fig.I

2

3.Lower the spindle (2) by turning the feed handles (3) counterclockwise.

4.Push the chuck up onto the spindle (2). Tap gently to ensure seat.

5.Open the jaws of the chuck (t) by rotating the chuck sleeve clockwise. To prevent damage, make sure the jaws are completely receded into the chuck.

Fig. J

2 --

Fig. M

E

MOUNTING DRILL PRESSTO WORK SURFACE (FIG. L)

1.If mounting the drill press to a workbench, a solid wood bench is preferred over a plywood board, to reduce noise and vibration.

2.Holes should be pre-drilled through the supporting surface.

3.The hardware to mount this drill press is NOT

supplied with the tool. The hardware as shown in the illustration should be used:

	Fig.	L	I
1.	Drill	press base
2.	Boft		i I
3.	Flat	washer
4.	Rubber washer		Ii

5.Worksurface

6.Flat washer

7.Lockwasher !

Hex nut	__	It
		i	i	.......................
8.9. Jam nut	_\			E
	\	tt
	"1	6	_
	5

ALIGNING THE BELT PULLEYS ,(FIG. N)

Open the t_ead cover of the Drill Press. Check alignment of the pulleys with a straight edge (5) such as a framing square, a level, or a piece of wood. Lay the straight edge across the top of the pulleys. If all three pulleys are NOT aligned:

1.Release belt pressure by loosening the belt tension lock knobs (2)on either side of the head, counterc!ockwise.

2.Loosen the motor mount nuts (3). Lift or lower the motor (4) until the pulleys are in line.

3.Tighten the motor mount nuts (3) t_sing an adjustable wrench.

NOTE: To avoid rattles or other noise, the motor housing should not touch the lower belt guard housing.

4, Retighten the belt by pulling the motor (4) toward or away from the drill press head, until the belt deflects approximately t/2 inch when pressed in the center.

NOTE: Refer to the chart inside the bett guard cover for recommended drilling speeds and belt / pulley positions.

,. Lock the belt tension lock knobs (2) by turning clockwise.

NOTE: When the belt is new, it may be difficult to move the belt. As the machine is used, the belt will gain more elasticity and will be easier to adjust.

Fig. N

¢h

ti

3

,,_ ........>s

...........i 3 :::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::