Craftsman 137.2191 owner manual General Safety Instructions

SECTION					PAGE
Warranty		...................		"	..... 2
Product	Specifications		...........................................		2
Safety	instructions				3
Accessories		and Attachments			6
Carton	Contents				6
Know	Your	DYII Press			8

GENERAL SAFETY INSTRUCTIONS

BEFORE USING THE DRILL PRESS

Safety is acombination of common sense, staying alert and knowing how to use your drill press.

!4. REMOVE ADJUSTING KEYS AND WRENCHES. From the habit of checking to see that keys and adjusting wrenches are removed from the t0ol before turning "ON".

15.NEVER LEAVE TOOL RUNNING UNATTENDED. TURN THE POWER "OFF". Don'tleave the tool untit it comes to a complete stop.

Glossary	of Terms			9
Assembly	and	Adiustments		10
•		.	..............................	t6
Operation	...............................			.20
Maintenance	............................................................
Troubl÷shooting		guide		21
Parts				22
Espaiol			"	25

FULL ONE YEAR WARRANTY

If this product fails due to a defect in material or workmanship within one year from the date of purchase, Sears will repair it free of charge.

Contact a Sears Service Center for repair.

_fthis product is used for commercial or rental purposes, this warranty applies onfy for 90 days from the date of purchase.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Soars, Roebuck and Co., Dept. 817 WA, Hoffman Estates, JL 60179

ii

i!

]

!

!

To avoid mistakes that could cause serious injury, do not plug the drill press in until you have read and understood the following:

1'. READ and become familiar with this entire instruction manual. LEARN the tool'sapplications, limitations, and possible hazards.

2.KEEP GUARDS IN PLACE and in working order.

3.DON'T USE IN A DANGEROUS ENVIRONMENT. Don'tuse power tools in damp or wet locations, or expose them to rain. Keep work area well lighted.

4.DO NOT use power tools in the presence of flammable liquids or gases.

5.KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.

6.KEEP CHILDREN AWAY. All visitors should be kept at a safe distance from the work area.

,DON'T FORCE THE TOOL. It will do the job better and safer at the rate for which it was designed.

,USE THE RIGHTTOOL. Don'tforce tool or the attachment to do a job for which it was not designed.

g÷ WEAR PROPER APPAREL. DO NOT wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Nonslip footwear is recommended. Wear protective hair covering to contain long hair.

16.NEVER STAND ON TOOL. Serious iniury coutd occur

if the tool is tipped o_'i_the cutting too! is unintentonalty contacted.

17.DON'T OVERREACH° Keep proper footing and balance at all t._,__s.

18.MAINTAIN TOOLS WiTH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories.

19.CHECK FOR DA_]AGED PARTS. Before. further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it wi!l operate properly and perform its intended function. Check for alignment of moving parts, binding of rnoving parts, breakage of parts, mounting, and any other conditions

that may affect its operation. A guard or other part that is damaged should be Properly repaired or replaced.

20.MAKE WORKSHOP KID PROOF with padlocks, master switches, or by removing starter keys.

2t. DO NOT operate the tool if you are under the influence of any drugs, alcohol or medication that could affect your ability to use the tool properly.

22, Dust generated from certain materials can be hazardous to your health. Always operate the drill pres.s in a weflwentilated area and provide for proper du#t removal. Use dust collection systems whenever possible.

CHUCK SIZE	1/2"
SPEEDS	5 (540-3,600 RPM)
£aOTOR	120V, 60 HZ, 6 AMPS,
HORSEPOWER	1/2 HP (Max. Developed)
TABLE SIZE	8-!/4" x 7-1/4"
TABLE TILT	450 RIGHT OR LEFT
SPINDLE TRAVEL	..... 2-3/8"
THROAT	5"
BASE SIZE	14-318" x 8-114"

To avoid electrical hazards, fire hazards, or damage to the tool, use proper circuit protection.

Your drill press is wired at the fac[[ory for 120V operation. Connect to a 120V, t5 AMP branch circuit and use a

i5 AMP time delay fuse or circuit breaker. To avoid shock or fire, replace power cord immediately if it is worn, cut or damaged in any way.

10.WEAR A FACE MASK OR DUST MASK. Drilling operation produces dust.

11.DISCONNECT TOOLS before servicing, and when

changing accessories, such as blades, bits, cutters, and the like.

12, REDUCE THE RISK OF UNINTENTIONAL STARTING.. Make sure the switch is in "OFF" position before plugging in.

13.USE RECOMMENDED ACCESSORIES. Consult the owner's manual for the recommended accessories.

The use of improper accessories may cause risk of injury to persons.

W_AaYOUa23. ALWAYS WEAR EYE PROTECTION. Any drit press

can throw foreign objects into the eyes which could cause

permanent eye damage. ALWAYS wear Safety Goggles (not glasses) that comply with

ANSI safety standard Z87.!. Everyday eyeglasses have only impact-resistant lenses. They ARE NOT safety glasses, Safety Goggtes are available at Sears. NOTE: Glasses or goggles not in compliance with ANSI Z87.1 could seriously hurt you when they break.

H51GHT 28-3/8"

SAVE THESE INSTRUCTIONS

)i:i;;i:!ii!!i)]!;::)::::!;:::)!i,::¸¸i;::i,<Sfi::,):i i,:::i:/:<:?::¸:LI::::,i:::_!:,:47T,!,:¸:;:::::':ii:i!:i'i;i:il:)!::!:i!f:i:!i::i;i:!:IT::):::i _)!:i:!I:I:I:':):i,:!:i::,):::!i:):))):ili:!i2_:i!:::i:i!,i_:ii::)!!::::i;i!;i::i:Tj::?:i::i!::<i':: :!::!:2¸I:::i!I__IYU::)i,Iii::i:))I)::(:_::_;i:ii{:::::::::,:!;i:ii=_::{::ii!)(i¸;i::i!;!;!¸!::I:'::::!?::?i!i:::i:!:i:;:i':!::_%)<];::i:_))i);:!:i!i!)::':ii:!_

3