TOREPLACECUTTINGLINE(Fig.14)
REMOVETHESPOOL
Foreasy spool replacement we recommend using Craftsman
1.Disconnect the trimmer from the power supply. Turn trimmer over to access spool head cover.
from the power outlet BEFORE installing parts or cleaning the trimmer
I_ WARNING: To avoid injury, ALWAYS turn off and disconnect the trimmer or making any adjustments.
FILLING | SPOOL WITH |
|
|
CUTTING | LINE cont. (Fig. 15) | Fig. 15 |
|
4. When the wound cutting line reaches the | RIGHT | WRONG | |
|
|
eyelets (recesses), cut the line. Temporarily
park the line in the spool rail notch on one side of the spool as shown in Fig. 15.
5.Repeat the above procedure for the second cutting line on the lower section of the spool.
6.Fit the spool onto the tool as described in "REPLACE THE SPOOL" page 20.
2. | Press | the release tabs on the spool head |
| cover and remove cover, pulling it straight | |
| off of spool. | |
3. | Lift the spool out of the spool housing. | |
REPLACE | THE SPOOL | |
1. Replace the spool with a new | ||
| factory |
Spool Head Cover
Fig. 14
Release tabs
cutting line. Ensure that cutting line is present i _ CAUTION: Before you begin trimming,
(Fig. 15).
OPERATING TIPS
in both sections of the spool. only use the appropriate type of
Sears store or other Craftsman outlet. |
2. Insert the end of one line through |
an eyelet in the spool housing. |
Insert the other line through the |
other eyelet. |
3. Insert the spool into housing and |
press it down gently until you feel |
it drop into place.Take care to keep |
the line from becoming trapped |
under the spool. |
4. Snap the spool head cover back on |
and at the same time pull lines and |
be sure that they are released from |
spool rail notch. |
FILLING SPOOL WITH CUTTING LINE
(Figs. 15)
Spool
Rail
Notch
Cutting Line
_ooI Rail Notch
1.Before each use make sure the protective safety guard is securely installed. Tighten the guard screws, but DO NOT over tighten.
2. | Be sure to check | the auxiliary | handle before each use, to make sure | it is firmly |
| |||
| tightened into desired working position. |
|
|
|
|
| ||
3. | Before trimming, | inspect the | area for string, wire, branches, | rocks, toys, or other | ||||
| objects that could be entangled in or thrown by the cutting line. |
|
|
| ||||
4. | Stand with the cutting head tipped down | at an angle in front, | guiding | the trimmer | in a | |||
|
|
|
|
|
| |||
5. | Cut from left to right whenever | possible. | Cutting to the right improves | the unit'scutting | ||||
| efficiency and clippings are thrown away from the operator. |
|
|
|
| |||
6. | To produce a smoothly trimmed area, move the trimmer in and | out of the area being | ||||||
| cut with constant speed and height. |
|
|
|
|
| ||
7. | Use only the tip of the cutting | line to do the trimming, especially | near walls and | fences. | ||||
| Trimming with the side of the cutting line may overload the motor, wear out the line | |||||||
| faster, and break the line more often. |
|
|
|
|
| ||
8. | DO NOT rest the trimmer spool on the ground while you are trimming. | This will cause | ||||||
| spool wear. |
|
|
|
|
|
|
|
You may wind new cutting line onto an empty spool. Replacement packs of 0.065 inch (1.65ram) Craftsman Cutting Line
1. Remove the empty spool from | the tool | Cutting Line |
as described in "REMOVE THE | SPOOL" above. |
|
2.Remove any remaining cutting line from the spool.
3.First wind new line onto the uppermost part of the spool. Feed 3/4 inch of cutting line into one of the line spool rail notches. Wind the cutting line onto the spool in the direction of the arrow on the spool. Make sure to wind the line neatly and in layers Do not crisscross (see Fig. 15).
20
9. | When cutting | vegetation that is over 6 inches in height, work from top to bottom | |||
| in small increments to avoid premature line wear or engine drag. |
| |||
10. | When the trimmer is stopped and the spool stops rotating, the cutting | line wilt relax | |||
| and may recede. Feed extra cutting line before storing the trimmer to prevent losing | ||||
| the line in the spool housing. |
|
| ||
11. | If the diameter | of the cutting | area gets smaller, | the line is worn down | and needs to be |
| advanced. |
|
|
|
|
12. | If the trimmer | is not cutting | correctly, the cutting | line may not be feeding properly. | |
| Remove and rewind the line spool. |
|
| ||
| (See FILLING SPOOL WITH CUTTING LINE, pg. 20). |
|
21