another free manual from www.searstractormanuals.com
| To assemble your Mower you will need: |
|
|
|
| a 9/16" Wrench and a Hammer |
|
|
|
| When R.H. (Right Hand) or L.H. (Left Ha nd) is |
|
|
|
| used, it means from a position behind the |
|
|
|
| steering wheel as if you were seated on the |
|
|
|
| tractor seat and facing forward. |
|
|
|
| ASSEMBLY |
|
|
|
| 1.1nstall Lift Lever using: |
|
|
|
| @0 |
|
|
|
| two Flat Washers, two Lockwashers and two Hex Nuts |
|
|
|
| found in bag of parts. |
|
|
|
| a. Place Lift Leve r (Fig. 1) over Lever Quadrant and t ilt |
|
|
|
| bottom of Lever outward to align Bolts in Lift Shaft |
|
|
|
| Weldme nt with holes in Lever. |
|
|
|
| b. Install Lift Lever to end of Lift Shaft Weldment (Fig. 1). |
|
|
|
| Be sure Lift Lever Bracket straddles Lever Quadrant and |
|
|
|
| that Lever fits on end of Lift Shaft. Secure with Flat |
|
|
|
| Washers, Lockwashers and Hex Nuts. Tighten Nuts se· |
|
|
|
| cu rely . |
|
|
|
| c. Depress Lever Plunger and move Lift Lever to middle of |
|
|
|
|
|
|
| |
| Lever Quadrant. Drive Drive Lock Pin through Lever, |
|
|
|
| Lever Quad rant and Lift Lever Bracket. |
|
|
|
| ASSEMBLE MOWER TO TRACTO r | |||
| 1. Check tra ctor tire pressure for proper inflation. | - |
| |
|
| |||
| 2.Drive tractor to an area that is smooth and level. |
| ||
|
|
|
| |
| 3 . Position mower on R.H. side of tractor as shown (Fig. 2). |
|
|
|
| 4.Turn tractor steering wheel to the extreme left. |
|
|
|
| 5 . Lock all four Attaching Plu ngers in the "OUT" position. |
|
|
|
| 6. Move Lift Lever to the extreme rear position. |
|
|
|
| 7. Slide mower under tractor until Suspension Arms are |
|
|
|
| direct ly beneath Hangar Brackets. NOTE : Be sure end of |
|
|
|
| Snu bber Pull Rod is extending to front of tractor and be· |
|
|
|
| tween fro nt wheels. |
|
|
|
| 8 .For ease in attaching mower to tractor, p lace a two foot |
|
|
|
| long 2 x 4 (or similar object) flat w ise unde r each e nd of |
|
|
|
| mower (Fig. 3). |
|
|
|
| 9. Move Lift Lever to the extreme forward position. |
|
|
|
| 10 .Grasp suspension arms by the Spring Boxes. Raise R. H. |
|
|
|
| suspension arms and a lign w ith holes in Front and Rear |
|
|
|
| Hangar Brackets. |
|
|
|
| 11. Release fron t Plunger so that Plunger enters hole in R.H. |
|
|
|
| Fro nt Hanger Bracket. |
|
|
|
| 12.Release rear Plunger so that Plunger ent ers slot in R. H. Rear |
|
|
|
| Ha nger Bracket. |
|
|
|
| 13 . Repeat ste ps 10, 11 and 12 for L.H . side of mower. |
|
|
|
| 14 . Pull Lift Lever back to lift mower. |
|
|
|
FIGURE 3 | 15 . Remove Blocks f rom under each end of mower. |
|
|
|
2x4 |
|
|
| |
............................... | . 2 . |
|
|
|
|
|
|
|
|