Manuals / Craftsman / Lawn and Garden / Lawn Mower

Craftsman 917.2720601 manual To Adjust Brake, With Parking Brake, Nut Jam Nut

Models: 917.2720601

1 60

Download 60 pages 2.95 Kb

Page 25

Mandrel

Idler

ianq

Pulley

TO ADJUST BRAKE

Your tractor is equipped with an adjustable brake system which is mounted on the side of the transaxle.

If tractor requires more than six (6) feet stopping distance at high speed in highest gear on a level dry concrete or paved surface, then brake must be adjusted.

1.Depress clutch/brake pedal and engage parking brake.

2.Measure distance between brake operating arm and nut "A" on brake red.

3.If distance is other than 1-9/16". loosen jam nut and turn nut "A" until distance becomes 1_9/16". Retighten jam nut against nut "A".

4.Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than six (6) feet in highest gear, further maintenance is necessary.

Contact a Sears or other qualified service center.

With Parking Brake

_"Engaged

'_=_._

N_utJam Nut

_-J_/_°_--_Operating

D_N6tAro touch this nut. If furth_brake

adjustment is necessary contact a Sears or other qualified service center.

TO REPLACE MOTION DRIVE BELT

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL-

1. Remove mower (See =TO REMOVE

MOWER" in this section of manual). NOTE: Observe entire motion drive belt

and position of all belt guides and keepers.

2.Remove belt from stationary idler and

clutching idler.

3, Remove belt downward from around

engine pulley.

4, Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades.

5.Remove belt from center span keeper and pull belt away from tractor.

BELT INSTALLATION -

1.Carefully work new belt down around transmission cooling fan and onto the input pulley.

2.Slide belt into the center span keeper.

3.Pull belt toward front of tractor and roll

around the top groove of engine pulley.

4.Install belt through stationary idler and clutching idler.

5.Make sure belt is in all pulley grooves

and inside all belt guides and keep- ers.

6.Install mower (See =TO INSTALL

MOWER" in this section of manual).

Engine Pulle

Clutching

Stationary Idler

Center S

Keeper

Transmission

Input Pulley

25

Image 25

Craftsman 917.2720601 manual To Adjust Brake, With Parking Brake, Nut Jam Nut, To Replace Motion Drive Belt

Contents

Sears Craftsman Help Line 5 am 5 pro, Mon Sat IcraftsmaniLimited Warranty on Craftsman Riding Equipment General Operation II. Slope OperationDo not IV. ServicePage Customer Responsibilities Repair Agreement28 x 1-1/4 For Future UseBefore Removing Tractor from Skid Attach Steering Wheel To Remove Tractor from CartonLabel Terminal Install SeatRelease parking brake by depressing clutch/brake pedal To Convertto Bagging or Discharging Install Mulcher Plate Check Brake SystemCheck Tire Pressure Check Deck LevelnessAutomatic Models only Plunger Know Your TractorFreewheel Control Disengagages transmission for pushingHOW to USE Your Tractor To Operate on Hills To Adjust Gauge WheelsGaug To Operate MowerADD Gasoline Before Starting the Engine Check Engine OIL LevelTo Start Engine Purge Transmission AutomatictransmissionwarmupMulching Mowing Tips Mowing TipsGeneral Recommendations Lubrication ChartCh=,v-Bait Before Each USETractor BatteryBrake Operation TiresEngine Engine OIL Filter Clean AIR ScreenAIR Filter Clean AIR INTAKE/COOLING Areas CleaningMuffler Spark PlugsTractor To Install MowerTo Remove Mower PulleySIDE-TO-SIDE Adjustment To Level Mower HousingFRONT-TO-BACK Adjustment Belt InstallationWith Parking Brake To Adjust BrakeNut Jam Nut To Replace Motion Drive BeltTo Adjust Steering Wheel ALIGN- Ment Transaxle Motion Control Lever Neutral AdjustmentTransmission REMOVAL/REPLACE- Ment Front Wheel TOE-IN/CAMBERReplacing BAI-FERY To Remove CABLES, Reverse OrderTo Replace Headlight Bulb Interlocks and RelaysThr ttle Idle Speed AdjustingI To Adjust CarburetorAcceleration Test ScrewTractor OtherEngine Problem Troubleshooting ChartCause Correction Problem Cause Correction Troubleshooting ChartFast Problem Cause CorrectionSlow OFFTractor --MODEL Number SchematicElectrical TRACTOR-- ModelnumberKEY Part Description Tractor --MODEL Number ElectricalTractor -- Model Number 917.2720601 Chassis and Enclosures KEY Part Description Tractor --MODEL Number 917.2720601 Chassis and EnclosuresTRACTOR-- Model Number Grounddrive Ground Drive Tractor -- Model Number 917.2720601 Steering Assembly KEY Part NO. NO. Description Tractor - Model Number 917.2720601 Steering AssemblyOptional Equipment Tractor -- Model Number EngineSpark Arrester KEY Part NO. no Description Tractor -- Model Number LiftassemblySeat Assembly Wheels & Tires Tractor --MODEL Number DecalsMowerdeck Mower Deck Mi= 142883 Tractor -- Model Number Hydro Gear Transaxle - Model NumberCylinder HEAD, Valve and Breather Crankcasej KEY Part NO. no 041 03-S3NITIONIELECTRICAL Blower Housing and Baffles AIR Intake Not Illustrated Starting System Engine Controls OIL PAN I Lubrication J Starting System KEY Part Description OIL PAN/LUBRICATIONCrankshaftexhaust SKit, solenoid repair SScrew, thread forming M5x0.8xlPage Suggested Guide for Sighting Slopes for Safe Operation M 5 pm., CST, Mort.- Sat Rn.-8 p m. EST, M- F, 4 p m S 6am -11 pm, 7 daysaweekSU-HOGAR sa 888-784.-6427