TO INSTALL MOWER

1.Raise attachment lift lever to its highest position.

2.Slide mower under tractor with deflec- tor shield to right side of tractor.

3.Lower lift lever to its lowest position.

4.Connect front links to mower deck and secure with retainer springs.

5.Connect suspension arms to rear deck brackets and secure with retainer

springs.

6.Connect anti-sway bar to chassis bracket and secure with retainer spring.

7.Push clutch cable housing guide into bracket, slide collar onto guide and secure with large retainer spring.

8.Place flat washer and clutch spring on idler pulley bolt and secure with small retainer spring.

9.Install belt onto engine pulley.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure

tires are properly inflated (See "PROD- UCT SPECIFICATIONS" section of this

manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of

mower to ground. Distance "A" on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make ad- justment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 1/8".

• Recheck measurements after adjusting.

FRONT-TO-BACK ADJUSTMENT IMPORTANT: Deck must be level side-to side. If the following front-to-back adjust- ment is necessary, be sure to adjust both

front links equally so mower will stay level side-to-side.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

Check adjustment on right side of trac- tor. Measure distance "D" directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjust- ments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut "E"

on both front links an equal number of turns.

•When distance "D" is 1/8" to 1/2"

lower at front than rear, tighten nuts "F" against trunnion on both front links.

•To raise front of mower, loosen nut "F" from trunnion on both front links. Tighten

nut "E" on both front links an equal num- ber of turns. The two front links must

remain equal in length.

•When distance "D" is 1/8" to 1/2" lower

at front than rear, tighten nut "F" against trunnion on both front links.

•Recheck side-to-side adjustment.

Both Front Links Should be Equal in Length

Bottom edge

Bottom edge

of mower to

of mower to

Jt"E"

Arm

Lift Link N_

Adjustment

Front Links

23

Page 22 Page 24
Page 23
Image 23
Craftsman 917.27268 manual To Level Mower Housing, SIDE-TO-SIDE Adjustment
Page 22 Page 24

917.27268 specifications

The Craftsman 917.27268 is a standout model in the realm of riding mowers, designed to offer powerful performance combined with ease of use for both residential and commercial lawn care. This versatile riding mower is equipped with a host of features that make it a valuable asset for maintaining lush and healthy lawns.

One of the most notable aspects of the Craftsman 917.27268 is its robust engine. Powered by a reliable 19 horsepower Briggs & Stratton engine, this mower provides ample power to tackle tough terrains and thick grass. The engine is paired with an automatic transmission that allows for smooth and effortless speed adjustments, ensuring that operators can easily navigate through their lawns without any hassle.

The mower's cutting deck is another standout feature. With a 42-inch cutting width, it allows for efficient mowing, reducing the number of passes needed to cover large areas. The deck also has a three-blade system, which ensures a clean and even cut every time. Additionally, the cutting height can be easily adjusted to meet the specific needs of your lawn, offering six different height settings for an optimal finish.

Ergonomic design is a key characteristic of the Craftsman 917.27268. It features a comfortable seat with a high backrest that provides ample support during extended mowing sessions. The steering wheel is positioned for enhanced control, allowing users to maneuver the mower with confidence. The mower also includes a foot-operated deck lift for straightforward height adjustments, making it user-friendly for individuals of all skill levels.

When it comes to technology, the Craftsman 917.27268 incorporates various features designed to enhance functionality. For instance, it boasts an integrated mulching capability, allowing clippings to be finely chopped and returned to the lawn as natural fertilizer. This not only saves time but also promotes healthier grass growth. Additionally, the mower is equipped with a sturdy frame and durable wheels that ensure stability and longevity, reinforcing its position as a reliable choice for lawn maintenance.

In conclusion, the Craftsman 917.27268 delivers power, versatility, and user-friendly features, making it an ideal choice for anyone looking to maintain their lawn effectively. Its combination of a capable engine, efficient cutting system, ergonomic design, and thoughtful technologies creates an appealing package for homeowners and lawn care enthusiasts alike.
Top Page Image Contents