_°e_ddlightWire

Connector

ENGINE

Maintenance, repair, or replacement of the emission control devices and systems, which are being done at the customers ex- pense, may be performed by any non-road engine repair establishment or individual. Warranty repairs must be performed by an authorized engine manufacturer's service outlet.

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be nec- essary. Check adjustment as described below before loosening cable. If adjust- ment is necessary, proceed as follows:

1.With engine not running, move throttle control lever from slow to choke posi- tion. Slowly move lever from choke to fast position.

2.Check that holes "A" in governor control lever and hole in governor plate line-up. If holes "A" are not aligned, loosen clamp screw and move throttle cable until holes are aligned. Tighten

clamp screw securely. Governor Control Lever

Governor Control Plate

in fuel, temperature, altitude or load. If the

carburetor does need adjustment, proceed as follows:

In general, turning idle mixture valve in (clockwise) decreases the supply of fuel to the engine giving a leaner fuel/air mix- ture. Turning the idle mixture valve out (counterclockwise) increases the supply

of fuel to the engine giving a richer fuel/air mixture.

IMPORTANT: Damage to the needle valve and the seat in carburetor may result if screw is turned in too tight.

PRELIMINARY SETTING -

1.Air cleaner assembly must be assem- bled to the carburetor when making carburetor adjustments.

2.Be sure the throttle control cable is adjusted properly (see above).

FINAL SETTING -(See "TO ADJUST THROTTLE CONTROL CABLE" in this

section of the manual.)

1.Start engine and allow to warm for five minutes. Make final adjustments with engine running and shift/motion control lever in neutral (N) position.

2.Move throttle control lever to slow posi- tion. With finger, rotate and hold throttle lever against idle speed screw. Turn idle speed screw to attain 1750 RPM.

3.While still holding throttle lever against idle speed screw, turn idle mixture valve full travel clockwise then coun- terclockwise until engine runs rough. Turn valve to a point midway between those two positions. Release throttle lever.

\

\

\

\

)ttle Cable

Holes "A" Clamp Screw

TO ADJUST CARBURETOR

NOTE: The carburetor on this engine is low emission. It is equipped with an idle fuel adjusting needle with a limiter cap, which allows some adjustment within the limits allowed by the cap. Do not attempt to remove the limiter cap. The limiter cap cannot be removed without breaking the adjusting needle.

The carburetor has been preset at the factory and adjustment should not be nec- essary. However, minor adjustment may be required to compensate for differences

27

Page 26 Page 28
Page 27
Image 27
Craftsman 917.27268 manual To Adjust Throttle Control Cable, Preliminary Setting, To Adjust Carburetor
Page 26 Page 28

917.27268 specifications

The Craftsman 917.27268 is a standout model in the realm of riding mowers, designed to offer powerful performance combined with ease of use for both residential and commercial lawn care. This versatile riding mower is equipped with a host of features that make it a valuable asset for maintaining lush and healthy lawns.

One of the most notable aspects of the Craftsman 917.27268 is its robust engine. Powered by a reliable 19 horsepower Briggs & Stratton engine, this mower provides ample power to tackle tough terrains and thick grass. The engine is paired with an automatic transmission that allows for smooth and effortless speed adjustments, ensuring that operators can easily navigate through their lawns without any hassle.

The mower's cutting deck is another standout feature. With a 42-inch cutting width, it allows for efficient mowing, reducing the number of passes needed to cover large areas. The deck also has a three-blade system, which ensures a clean and even cut every time. Additionally, the cutting height can be easily adjusted to meet the specific needs of your lawn, offering six different height settings for an optimal finish.

Ergonomic design is a key characteristic of the Craftsman 917.27268. It features a comfortable seat with a high backrest that provides ample support during extended mowing sessions. The steering wheel is positioned for enhanced control, allowing users to maneuver the mower with confidence. The mower also includes a foot-operated deck lift for straightforward height adjustments, making it user-friendly for individuals of all skill levels.

When it comes to technology, the Craftsman 917.27268 incorporates various features designed to enhance functionality. For instance, it boasts an integrated mulching capability, allowing clippings to be finely chopped and returned to the lawn as natural fertilizer. This not only saves time but also promotes healthier grass growth. Additionally, the mower is equipped with a sturdy frame and durable wheels that ensure stability and longevity, reinforcing its position as a reliable choice for lawn maintenance.

In conclusion, the Craftsman 917.27268 delivers power, versatility, and user-friendly features, making it an ideal choice for anyone looking to maintain their lawn effectively. Its combination of a capable engine, efficient cutting system, ergonomic design, and thoughtful technologies creates an appealing package for homeowners and lawn care enthusiasts alike.
Top Page Image Contents