Manuals / Craftsman / Lawn and Garden / Lawn Mower

Craftsman 917.273062 To Adjust Choke Control, To Adjust Carburetor, Preliminary Setting

Models: 917.273062

1 68
Download 68 pages 13.65 Kb
Page 31
Image 31

TO ADJUST CHOKE CONTROL

The choke control has been preset at the factory and adjustment should not be necessary, check adjustment as de- scribed below before loosening cable. If

adjustment is necessary, proceed as follows:

1.With engine not running, move choke control (located on dash panel) to full choke position.

2.Remove air cleaner cover, filter and cartridge plate to expose carburetor choke (See "AIR FILTER" in the Maintenance section of this manual).

3.Choke should be closed. If it is not, loosen casing clamp screw and move choke cable until choke is completely closed. Tighten casing clamp screw securely.

4.Reassemble air cleaner.

Closed for Full

TO ADJUST CARBURETOR

The carburetor has been present at the factory and adjustment should not be necessary. However, minor adjustment may be required to compensate for

differences in fuel, temperature, altitude or load. If the carburetor does need

adjustment, proceed as follows:

In general, turning the adjusting needles in (clockwise) decreases the supply of fuel to the engine giving a leaner fuel/air mixture. Turning the adjusting needles out

(counterclockwise) increases the supply of fuel to the engine giving a richer fuel/ air mixture.

IMPORTANT: Damage to the needles and the seats in carburetor may result if screw is turned in too tight.

PRELIMINARY SETTING -

1.Be sure you have a clean air filter, and the throttle control cable is adjusted

properly (see "TO ADJUST

THROTTLE CONTROL CABLE" in the Service and Adjustments section of this manual).

2.With engine off turn idle fuel adjusting needle in (clockwise) closing it finger tight and then turn out (counterclock- wise) 1 turn.

FINAL SETTING -

1.Start engine and allow to warm for five minutes. Make final adjustments with engine running and shift/motion

control lever in neutral (N) position. NOTE: The high idle is set at the factory and cannot be adjusted.

2.Idle speed setting - With throttle control lever in slow position, engine should idle at 1200 RPM. If engine idles too slow or fast, turn idle speed adjusting screw in or out until correct idle is attained.

3.Idle fuel needle setting - With throttle control lever in slow position, turn idle fuel adjusting needle in (clockwise) until engine speed decreases and then turn out (counterclockwise) approximately 3/4 turn to obtain the best low speed performance.

4.Recheck idle speed. Readjust if necessary.

ACCELERATION TEST -

5.Move throttle control lever from slow to fast position. If engine hesitates or dies, turn idle fuel adjusting needle

out (counterclockwise) 1/8 turn. Repeat test and continue to adjust, if

necessary, until engine accelerates smoothly.

High speed stop is factory adjusted. Do not adjust-damage may result. IMPORTANT: Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous. If you think the engine-governed high speed needs adjusting, contact your nearest autho-

rized service center/department, which has proper equipment and experience to make any necessary adjustments.

31

Page 30 Page 32
Page 31
Image 31
Craftsman 917.273062 To Adjust Choke Control, To Adjust Carburetor, Preliminary Setting, Final Setting, Acceleration Test
Page 30 Page 32

917.273062 specifications

The Craftsman 917.273062 is a high-performance riding lawn mower designed for residential and light commercial use, blending efficiency, power, and ease of operation. This robust machine is ideal for users seeking to maintain larger lawns or properties with varying terrains.

One of the standout features of the Craftsman 917.273062 is its powerful engine. Equipped with a 19.5 horsepower Briggs & Stratton engine, this mower delivers reliable performance, offering ample power to handle thick grass and uneven surfaces. The engine's design ensures smooth operation with reduced noise levels, making mowing more pleasant.

The mower features a 42-inch cutting deck, allowing it to cover vast areas in a single pass. This deck design incorporates a twin-blade system, which enhances cutting efficiency and provides a clean, even cut. The adjustable cutting heights, ranging from 1.5 inches to 4 inches, allow users to customize their mowing experience based on their lawn's specific needs.

For improved maneuverability, the Craftsman 917.273062 features a tight turning radius, enabling users to navigate around obstacles such as trees, flower beds, and garden fixtures with ease. This is particularly advantageous for homeowners with intricate landscapes. The riding mower is also designed with a comfortable, high-back seat, which is ergonomically shaped to provide support and reduce fatigue during prolonged use.

Technologically, the mower includes a user-friendly dashboard that displays essential information, such as fuel level, speed settings, and maintenance reminders. This intuitive interface simplifies operation and helps users manage their mowing tasks effectively.

Another characteristic of the Craftsman 917.273062 is its ease of maintenance. The mower features an accessible cutting deck that makes it simple to clean and maintain the blades, ensuring optimal performance over time. Additionally, the mower is equipped with a fuel-efficient system, reducing the frequency of refueling and minimizing environmental impact.

In summary, the Craftsman 917.273062 combines power, efficiency, and user-friendly design to provide a superior mowing experience. Its combination of a robust engine, versatile cutting deck, ergonomic design, and ease of maintenance makes it a preferred choice for homeowners and landscape enthusiasts alike. Whether for routine lawn care or tackling overgrown areas, the Craftsman 917.273062 proves to be a reliable and effective solution.