Manuals / Craftsman / Lawn and Garden / Lawn Mower

Craftsman 917.27582 To Replace Mower Blade Drive Belt, To Level Mower Housing, Belt Removal

Models: 917.27582

1 56
Download 56 pages 25.19 Kb
Page 24
Image 24

7.Push clutch cable housing guide into bracket, slide collar onto guide and secure with large retainer spring.

8.Place flat washer and clutch spring on idler pulley bolt and secure with small retainer spring.

9.Install belt onto engine pulley.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See "PROD-

UCT SPECIFICATIONS" section of this

manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of

mower to ground. Distance "A" on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjust- ment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift

link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

Bottom edge

Bottom edge of

of mower to

mower to ground

0rouo0,

 

.....

 

 

Arm

O

 

Lift Link

Adjustment Nut -------

- --

FRONT-TO-BACK ADJUSTMENT IMPORTANT: Deck must be level side-to side. If the following front-to-back adjust- ment is necessary, be sure to adjust both front links equally so mower will stay level side-to-side.

To obtain the best cutting results, the mower housing should be adjusted so

that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in

its highest position.

Check adjustment on right side of trac- tor. Measure distance "D" directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjust- ments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut "E"

on both front links an equal number of turns.

•When distance "D" is 1/8" to 1/2"

lower at front than rear, tighten nuts "F" against trunnion on both front links.

•To raise front of mower, loosen nut "F" from trunnion on both front links. Tighten nut "E" on both front links an equal num- ber of turns. The two front links must remain equal in length.

•When distance "D" is 1/8" to 1/2" lower

at front than rear, tighten nut "F" against trunnion on both front links.

•Recheck side-to-side adjustment.

Oo\_

oo, _

Mandrel

Both Fron,t Links Should be. E,qual in Length

Nut "F"

Trunnion

Front Links

TO REPLACE MOWER BLADE DRIVE BELT

The mower blade drive belt may be re- placed without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

1.Remove mower from tractor (See "TO REMOVE MOWER" in this section of

manual).

2.Work belt off both mandrel pulleys and idler pulleys.

3.Pull belt away from mower.

24

Page 23 Page 25
Page 24
Image 24
Craftsman 917.27582 To Replace Mower Blade Drive Belt, To Level Mower Housing, SIDE-TO-SIDE Adjustment, Belt Removal
Page 23 Page 25

917.27582 specifications

The Craftsman 917.27582 is a standout machine in the realm of lawn tractors, known for its reliability and robust performance. This model is particularly favored by homeowners looking for a powerful, efficient, and user-friendly solution for lawn care, capable of handling a variety of landscaping tasks with ease.

One of the defining features of the Craftsman 917.27582 is its powerful engine. Equipped with a 19.5 horsepower Briggs & Stratton engine, it delivers reliable power that facilitates optimal cutting performance, making it suitable for tackling medium to large-sized lawns. The automatic transmission allows for smooth and effortless operation, enabling users to navigate through various terrains without the hassle of manual shifting.

The cutting deck of the Craftsman 917.27582 is another highlight, featuring a durable 42-inch deck width. This size not only allows for efficient mowing but also ensures that larger areas can be covered in less time. The deck is designed with a sturdy construction that withstands wear and tear, making it ideal for regular use. Additionally, the deck's six different cutting height adjustments permit customization based on the type of grass and current weather conditions, allowing users to achieve a tailored lawn care routine.

Comfort and ease of use are at the forefront of the Craftsman 917.27582's design. The oversized high-back seat provides ample cushioning and support, perfect for those extended mowing sessions. The user-friendly controls are intuitively placed, making it straightforward for operators to adjust settings without distraction.

Another notable characteristic is the integrated mulching capability, allowing users to maintain a healthy lawn by returning nutrients back into the soil. This feature minimizes lawn waste while promoting vigorous grass growth, a boon for eco-conscious gardeners.

The Craftsman 917.27582 also boasts functional storage options and a tiller attachment, enhancing its versatility. With its combination of powerful performance, user-centric design, and innovative features, the Craftsman 917.27582 stands out as a top contender for those seeking a dependable lawn tractor that simplifies lawn maintenance while delivering exceptional results. Its blend of technology and practicality caters to both novice users and experienced landscapers alike, making it a wise investment for any home.