Craftsman 917.28746 To Check Brake, Front Wheel Toe-In/Camber, To Remove Wheel For Repairs

TO CHECK BRAKE

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced.

You may also check brake by:

1.Park tractor on alevel, dry concrete or paved surface, depress clutch/brake pedal all the way down and engage parking brake.

2.Disengage transmission by placing freewheel control in "transmission dis- engaged" position. Pull freewheel con-

trol out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manually push the tractor forward. If the rear wheels rotate, then the brake needs to be serviced. Contact a Sears or other qualified service center.

FRONT WHEEL TOE-IN/CAMBER

Your new tractor front wheel toe-in and camber is set at the factory and is normal. The front wheel toe-in and camber are not adjustable. If damage has occurred to affect the factory set front wheel toe-in or camber, contact a Sears or other qualified service center.

TO REMOVE WHEEL FOR REPAIRS

Washers

I

~SqUareKey (Rear

Wheel Only)

TO START ENGINE WITH A WEAK BAT-

TERY

AWARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from bat- teries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BAT- TERY" in the MAINTENANCE section of this manual).

If "jumper cables" are used for emergency starting, follow this procedure: IMPORTANT: Your tractor is equipped with a12 volt system: The other vehicle must also be a 12 volt system. Do not use

REPLACING BATTERY

AWARNING: Do not short battery terminals by allowing a wrench or any other objectto contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from accidental grounding.

1.Lift hood to raised position.

2.Disconnect BLACK battery cable (A) then RED battery cable and carefully remove battery from tractor.

3.Install new battery with terminals in same position as old battery.

4.First connect RED battery cable (B) to positive (+) battery terminal with hex bolt and keps nut as shown. Tighten

securely. Slide terminal cover (C) over

.terminal.

5.Connect BLACK grounding cable to negative (-) battery terminal with re- maining hex bolt and keps nut. Tighten securely

6.Close hood.

TO REPLACE FUSE

Replace with 30 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL AS- SEMBLY

1.Raise hood.

2.Unsnap headlight wire connector.

3.Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

4.When replacing hood, be sure to re- connect the headlight wire connector.

1.Block up axle securely.

2.Remove axle cover, retaining ring and washers to allow wheel removal (rear wheels have a square key - Do not lose).

3.Repair tire and reassemble.

NOTE: On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

4.Replace washers and snap retaining ring securely in axle groove.

5.Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, purchase and use tire sealant from Sears. Tire sealant also prevents tire dry rot and corrosion.

your tractor battery to start other vehicles.

TO ATTACH JUMPER CABLES -

1.Connect one end of the RED cable to the POSITIVE (+) terminal of each battery(A-B), taking care not to short against tractor chassis.

2.Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

3.Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER-

1.BLACK cable first from chassis and then from the fully charged battery.

2.RED cable last from both batteries.

1.Raise hood.

2.Remove bulb holder from the hole in the backside of the grill.

3.Replace bulb in holder and install bulb holder securely back into the hole in the backside of the grill.

4.Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

ENGINE

Maintenance, repair, or replacement of the emission control devices and systems, which are being done at the customers ex- pense, may be performed by any non-road engine repair establishment or individual. Warranty repairs must be performed by an authorized engine manufacturer's service outlet.

CARBURETOR

If your engine does not operate properly due to suspected carburetor problems, take your tractor to a Sears or other qualified service center for repair and/or

adjustment.. High speed stop is factory adjusted. Do not adjust - damage may result.

IMPORTANT: Never tamper with the engine governor, which is factory set for proper engine speed. Overspeed- ing the engine above the factory high speed setting can be dangerous. If you think the engine-governed high speed needs adjusting, contact a Sears or other qualified service center" which has proper

Weak or Dead Fully Charged

BatteryBattery

•Check wiring. See electrical wiring diagram in the Repair Parts section.

equipment and experience to make any necessary adjustments.

28 29