Craftsman 917, 385141 manual Lawn Mower, Tires, Lubrication

÷L

LAWN MOWER

Always observe safety rules when per- forming any maintenance.

TIRES

•Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

BLADE CARE

For best results, mower blade must be kept sharp. Replace a bent or damaged blade.

CAUTION: Use only a replacement blade approved by the manufacturer of your mower. Using a blade not approved by the manufacturer of your mower is hazardous, could damage your mower and void your warranty.

TO REMOVE BLADE

1.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

2.Turn lawn mower on its side. Make sure air filter and carburetor are up.

3.Use a wood block between blade and mower housing to prevent blade from

turning when removing blade bolt. NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

®4. Remove blade bolt by turning counter- clockwise.

5.Remove blade and attaching hardware

(bolt, lock washer, hardened washer). NOTE: Remove the blade adapter and check the key inside hub of blade adapter. The key must be in good condition to work properly. Replace adapter if damaged.

TO REPLACE BLADE

1.Position the blade adapter on the en- gine crankshaft. Be sure key in adapter and crankshaft keyway are aligned.

2.Position blade on the blade adapter aligning the two (2) holes in the blade with the raised lugs on the adapter.

3.Be sure trailing edge of blade (opposite sharp edge) is up toward the engine.

4.Install the blade bolt with the lock washer and hardened washer into

blade adapter and crankshaft.

5.Use block of wood between blade and lawn mower housing and tighten the

blade bolt, turning clockwise.

•The recommended tightening torque is 35-40 ft. Ibs.

IMPORTANT: Blade bolt is heat treated. If bolt needs replacing, replace only with

approved bolt shown in the Repair Parts section of this manual.

Blade adapter Key Crankshaft

o

//

bolt	Hardened
	washer	•	Crankshaft

TO SHARPEN BLADE

NOTE: We do not recommend sharpening

blade- but if you do, be sure blade is balanced. An unbalanced blade will cause eventual

damage to mower or engine.

•The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, drive a nail into a beam or wall. Leave about one inch of

the straight nail exposed. Place center hole of blade over the head of the nail.

If blade is balanced, it should remain in

a horizontal position. If either end of the
blade moves downward, sharpen the
heavy end until the blade is balanced.
GRASS CATCHER
(If purchased as an accessory)	®

•The grass catcher may be hosed with water, but must be dry when used.

•Check your grass catcher often for dam-

age or deterioration. Through normal use it will wear. If catcher needs replac- ing, replace only with approved replace-

ment catcher shown in the Repair Parts section of this manual. Give the lawn

mower model number when ordering.

ENGINE

LUBRICATION

Use only high quality detergent oil rated with API service classification SG-SL. Select the

oil's SAE viscosity grade according to your expected operating temperature.

SAE VISCOSITY GRADES

F -20	0	30 32 40	60	80	100
c -_0	-2; -1;	;	1;	_0	10 4;

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather,

these multi-viscosity oils will result in in- creased oil consumption when used above 32°E Check your engine oil level more fre- quently to avoid possible engine damage

12 from running low on oil.

385141-es-412842_r0indd 12 4_ 2/23/2007 10:58:15AM