RULES FOR SAFE OPERATION (Continued)
NEVER USE IN AN EXPLOSIVE ATMO-
SPHERE. Normal sparking of the motor could
igniteflammable liquids, gases, or fumes.
KEEP HANDLES DRY, CLEAN, AND FREE •
FROM OIL AND GREASE. Always use aclean
cloth when cleaning. Never use brake fluids, •
gasoline, petroleum-based products or any
strong solvents toclean your tool.
STAY ALERT. Watch what youare doing and
use common sense. Do not operate tool when
you are tired, Do not rush.
CHECK DAMAGED PARTS. Before further use
of the tool, a guard or other part that is damaged
shouldbe carefully checked to determine that it
willoperate properly and perform its intended
function. Check for alignment ofmoving parts, •
binding of moving parts, breakage ofpads,
mounting, and any other conditions that may
affect its operation. Aguard or other part that is
damaged should be properly repaired or •
replaced by an authorized service center unless
indicated elsewhere in this instruction manual.
DO NOT USE TOOL IF SWITCH DOES NOT
TURN IT ON AND OFF. Have defective switches
replaced by an authorized service center.
DRUGS, ALCOHOL, MEDICATION. Do not
operate tool while under the influence of drugs, •
alcohol, or any medication.
DRILLING OR DRIVING SCREWS INTO
ELECTRICAL WIRING IN WALLS, CEILINGS,
OR OTHER AREAS CAN CAUSE THE BITOR •
CHUCK TO BECOME ELECTRICALLY LIVE.
Do nottouch metal parts when drilling into a wall;
grasp only the insulated handle(s) orplastic
housing when using this tool. Make sure hidden A
electrical wiring, water pipes, and mechanical AMk
hazards are not in the path of the bit when
drillinginto awall.
•INSPECT FOR and remove all nails from lumber
before drilling.
IMPORTANT SAFETY RULES FOR BA'n'ERY
TOOLS
Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in
operating condition. Be aware of possible
hazards when not using your battery tool or
when changing accessories.
USE ONLY THE CHARGER PROVIDED WITH
YOUR BA'n'ERY TOOL. Do not substitute any
other charger. Use of another charger could
cause batteries to explode causing possible
serious injury.
DO NOT PLACE BATTERY TOOLS OR THEIR
BATTERIES NEAR FIRE OR HEAT. They may
explode.
DO NOT CHARGE BATTERY TOOL IN A
DAMP OR WET LOCATION.
Your battery tool should be charged in alocation
where the temperature is more than 50°F but
less than 100°F.
Under extreme usage or temperature conditions,
battery leakage may occur. If liquid comes in
contact with your skin, wash immediately with
soap and water, then neutralize with lemon juice
or vinegar. If liquid gets in your eyes, flush them
with clean water for at least 10 minutes, then
seek immediate medical attention.
If carrying your battery tool at your side, make
sure it is not running and your finger isnot on the
switch. Avoid accidental starting.
SECURE WORK before applying power. NEVER
hold workpiece in your hand or across your legs.
WHEN SERVICING USE ONLY IDENTICAL
CRAFTSMAN REPLACEMENT PARTS.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER
SAVE THESE INSTRUCTIONS, This manual
contains important safety and operating
instructionsfor battery charger item number
9.-11012 (981481-001).
Before using battery charger, read all instructions
and cautionary markings in this manual, on
battery charger, and product using battery
charger.
WARNING: To reduce risk of injury, charge only
nickel-cadmium type rechargeable batteries.
Other types of batteries may burst causing
personal injury and damage.
Do not expose charger to rain or snow.
Use of an attachment notrecommended or sold
by thebattery charger manufacturer may result
in a risk of fire, electric shock, or injury to
persons.
To reduce risk of damage to charger body and
cord, pull by charger body rather than cord when
disconnecting charger.
Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected
to damage or stress.