Craftsman 28986, ZTS 6000 manual Troubleshooting the Rider, Problem, Cause, Remedy, will, Awarning

Models: 28986 107.289860 ZTS 6000

1 116
Download 116 pages 42.77 Kb
Page 35
Image 35
Troubleshooting the Rider

Whilenormalcareandregularmaintenancewillextend thelifeofyourequipment,prolongedorconstantuse mayeventuallyrequirethatservicebeperformedtoallow ittocontinueoperatingproperlyThetroubleshooting.

guidebelowliststhemostcommonproblems,theircaus- esandremedies.

Ifyouprefer,alloftheseprocedurescanbeperformed foryoubya SearsParts& RepairCenterSeetheback.

coverforimportantSearsParts&RepairCenterinforma- tion.

Troubleshooting the Rider

AWARNING

To avoid serious injury, perform maintenance on the rider or mower only when the engine is stopped and the ground speed levers are set to PARK.

Always remove the ignition key, disconnect the spark plug wire and fasten it away from the plug before beginning the maintenance, to prevent accidental starting of the engine.

PROBLEM

CAUSE

 

 

 

 

 

REMEDY

 

 

 

 

 

 

 

Engine

will

Ground

speed levers not set to START/PARK.

Set to START/PARK.

 

 

 

 

not turnover

Mower

 

blade switch in ON position.

 

Place

in OFF

position.

 

 

 

or start.

 

Ground

speed levers not set to START/PARK.

Set to START/PARK.

 

 

 

 

 

 

 

 

 

 

 

 

Choke

 

not in CLOSED position.

 

Move choke to CLOSED

position.

 

 

 

L

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Ignition

switch not turned fully to START

position.

Turn ignition

switch fully to START position.

 

 

IOut of fuel.

 

 

 

 

Allow

engine

to cool, then refill the fuel tank.

 

 

iEngine

 

flooded.

 

 

 

Set choke to OPEN position when cranking engine.

 

 

Fuel is old or stale, or water

in fuel.

 

Drain

fuel

& replace

with fresh fuel. Contact Sears

 

 

 

 

 

 

 

 

 

Parts

& Repair.

 

 

 

 

 

 

 

iBattery

terminals

require cleaning.

 

Clean

the

battery

terminals.

 

 

 

 

IBattery

discharged

or dead.

 

 

Recharge

or replace.

 

 

 

 

 

 

Spark plug(s) faulty, fouled or incorrectly

gapped.

Clean

and gap or replace.

 

 

 

 

iWiring

 

loose or broken.

 

 

Visually check wiring

& replace

broken

or frayed

 

 

 

 

 

 

 

 

 

wires. Tighten

loose connections.

 

 

 

ISolenoid or starter

motor faulty.

 

Replace.

Contact

Sears

Parts & Repair.

 

 

iSafety

interlock switch faulty.

 

 

Replace. Contact

Sears

Parts & Repair.

 

Engine

starts

iAir filter

plugged.

 

 

 

Service pre=cleaner and/or replace air filter

hard or

runs

 

 

 

 

 

 

 

element.

 

 

 

 

 

 

 

poorly.

 

Choke

 

not set to CLOSED position when

 

Set choke to CLOSED when cranking.

Set choke to

 

 

icranking the engine, OR choke not set to OPEN

OPEN when

engine

is running.

Awarm

engine may

 

 

after engine

starts,

 

 

not require choking.

 

 

 

 

 

 

Spark

plug

faulty, fouled, or incorrectly gapped.

Clean

and gap or replace.

 

 

Engine

 

Low oil level.

 

 

 

Check/add

oil as required.

 

 

knocks,

 

iUsing

wrong grade oil.

 

 

See "Change

Engine

Oil" in the

Maintenance

 

 

 

 

 

 

 

 

 

Section.

 

 

 

 

 

 

 

Excessive oil

iEngine

 

running too hot.

 

 

Clean

engine

cooling

fins, blower screen and air

consumption,

 

 

 

 

 

 

 

cleaner.

 

 

 

 

 

 

 

 

 

iUsing

wrong weight oil.

 

 

See "Change

Engine

Oil" in the

Maintenance

 

 

 

 

 

 

 

 

 

Section.

 

 

 

 

 

 

 

 

 

Too much oil in crankcase.

 

 

Drain excess

oil.

 

 

 

 

 

Engine

 

iDirty air filter or pre-cleaner,

or both.

 

Service or replace as required.

See Maintenance

exhaust

is

 

 

 

 

 

 

 

Section.

 

 

 

 

 

 

 

black.

 

Choke

 

set to CLOSED when

engine is running.

Set choke to OPEN as soon as engine

starts.

35

Page 35
Image 35
Craftsman ZTS 6000, 107.289860 manual Troubleshooting the Rider, Problem, Cause, Remedy, will, Awarning