Engineruns,but Transmissionreleaseleversin PUSH
rider | will not | 9ositions. |
|
| |||
drive. |
|
|
| Drive belt slips, |
| ||
|
|
|
| Belt is broken, |
|
| |
|
|
|
| Parking brake is not fully released, | |||
Rider | drive | belt | Pulleys or belt greasy or oily, | ||||
slips. |
|
|
| Belt stretched | or worn. |
| |
|
|
|
|
| |||
Parking | brake | Parking | brake is incorrectly | adjusted, | |||
will not | hold. |
|
|
|
| ||
Rider | steers | or | Improper | tire inflation. |
| ||
handles | poorly. | Steering | linkage is loose, |
| |||
|
|
|
|
| |||
Rider | tracks | to | Ground | speed | adj. knobs | not adjusted, | |
one side. |
|
|
|
|
| ||
Moveleversto DRIVEpositions.
Clean or replace belt as necessary,
Replace drive belt, Contact Sears Parts & Repair, Contact Sears Parts & Repair,
Clean as required,
Replace belt. Contact Sears Parts & Repair. See Service & Adjustments Section,
See Maintenance Section.
Check and tighten any loose connections,
See SPEED BALANCING ADJUSTMENT in Service & Adjustments section,
Troubleshooting | the | Mower |
|
|
|
|
|
|
|
| |||||
PROBLEM |
| CAUSE |
|
|
|
|
| REMEDY |
|
|
|
| |||
Mower cutting | Cutting | height motor screw dirty or requires | Thoroughly | clean and | lubricate cutting height motor | ||||||||||
height | does | not | lube. |
|
|
|
|
| screw, |
|
|
|
|
| |
adjust. |
|
| Cutting | height | linkage | disconnected, | Check that | mower | linkage is connected, | ||||||
Mower cut is |
| Rider tires | not inflated | equally or properly. | See Maintenance | Section. |
| ||||||||
uneven. |
| Mower | not leveled properly, | See "Mower | Leveling" | in Service & Adjustments, | |||||||||
Mower | cut is | Engine | speed | too slow, | Always | set engine | speed to FAST when mowing, | ||||||||
rough | looking. | Ground | speed | too fast, | Decrease ground | speed, |
| ||||||||
|
|
| Blades | are dull, |
|
| Sharpen | or replace blades, See Maintenance | |||||||
|
|
|
|
|
|
|
|
| Section, |
|
|
|
|
| |
|
|
| Mower | drive belt slipping because it is oily or Clean or replace belt | as necessary, |
| |||||||||
|
|
| worn. |
|
|
|
|
|
|
|
|
|
|
| |
|
|
| Blades | not properly fastened to arbors. | See "Check/Replace | Mower Blades" | in Maintenance | ||||||||
|
|
|
|
|
|
|
|
| Section. |
|
|
|
|
| |
Engine | stalls |
| Engine | speed | too slow. | Always | set engine | speed to FAST when mowing. | |||||||
easily | with |
| Ground | speed | too fast, | Decrease Ground | Speed, |
| |||||||
mower | engaged. |
| |||||||||||||
Cutting | height set too low. | Cut tall | grass at maximum cutting height during first | ||||||||||||
|
|
| |||||||||||||
|
|
|
|
|
|
|
|
| 9ass. |
|
|
|
|
| |
|
|
| Underside | of mower deck dirty, | Remove | mower deck and clean underside, | |||||||||
|
|
| Discharge | chute | jamming with cut grass, | Cut grass with discharge pointing toward previously | |||||||||
|
|
|
|
|
|
|
|
| cut area, |
|
|
|
| ||
Excessive |
| Blade mounting | nuts | are loose, | Tighten | to |
| ||||||||
mower |
|
| Mower blades, arbors, or pulleys are bent, | Check and replace as necessary, |
| ||||||||||
vibration, |
| Mower | blades are out of balance, | Replace | or balance blades, See Maintenance | ||||||||||
|
|
| |||||||||||||
|
|
|
|
|
|
|
|
| Section, |
|
|
|
|
| |
|
|
| Belt installed incorrectly, | Reinstall correctly, |
|
|
| ||||||||
Mower drive | belt | Idler pulley spring broken or not properly | Repair or replace as needed, |
| |||||||||||
slips or fails | to | attached, |
|
|
|
|
|
|
|
|
|
| |||
drive, |
|
| Mower | drive belt broken, | Replace | drive belt, |
|
| |||||||
|
|
| PTO clutch | out of adjustment, | Adjust PTO clutch, | See Maintenance | Section, | ||||||||
36
