BX-440H / BX-4115 ThunderBass Amplifier
Using the Biamp Capabilities – BX-440H:
About Biamping: The Biamp High and Low outputs of the
to “biamp” your system: that is, using two amplifier/speaker combinations to share the task of reproducing the full range of your bass. Biamping increases each amplifier’s efficiency by allowing it to “focus” on a certain frequency range, rather than operating full range. The results of biamping include cleaner sound and more output power than that of a
There are a number of different ways to use the
The Biamp Controls: The front panel Crossover Frequency | C R O S S O V E R |
| |||||
control (#15) sets the point where the low frequency signal rolls |
|
|
|
|
| ||
off and the high frequency signal begins. This control is variable | FREQUENCY | BALANCE |
| ||||
from 100Hz to 1kHz. Adjust this control to best suit the fre- |
| ||||||
| 300 Hz |
|
|
| |||
quency range of your low frequency speaker cabinet. The |
|
|
|
|
| ||
Crossover Balance control (#16) proportions the signal between | 15 |
|
|
| 16 | ||
the high and the low output jacks (#26 and 27, rear panel). |
|
|
|
|
| ||
Adjust this control for the most appealling blend of lows and | 100 Hz | 1kHz | LO | HI |
| ||
highs. |
|
|
| ||||
|
|
|
|
|
|
| |
Example 1: |
|
|
| OUT |
| ||
|
|
|
|
| PREAMP |
|
|
|
|
| 1 |
|
|
| EFFECTS |
With the |
|
|
|
|
| LOOP | |
|
|
| IN |
| RETURN | ||
|
| from |
|
| PWR AMP |
|
|
cabinet for the low end; a | BX- |
|
|
|
| ||
bass |
|
| 1 |
| |||
220H and a |
| 3 |
|
| SEND | ||
|
|
|
| ||||
the high end: |
|
|
|
| S |
|
|
|
|
|
|
|
| ||
Plug your bass into the |
|
| P |
|
| ||
|
|
| 220W @ 4 OHMS |
| |||
|
|
|
|
| E |
|
|
(1) Run a shielded cable from | the |
|
|
| A 150W @ 8 OHMS |
| |
|
|
| R |
|
| ||
|
|
|
|
| K MIN. LOAD |
|
|
|
|
|
|
| E |
|
|
biamp high out jack of the |
|
|
| S |
| BALANCED | |
|
|
|
|
| |||
|
| input | 2 |
|
|
| LINE OUT |
the power amp in jack of the |
|
|
|
| |||
|
|
|
|
|
| ||
(2) Run a speaker cable from | the |
|
|
|
|
| |
|
|
|
|
|
|
| |
speaker out jack of the |
|
|
|
|
|
| |
input jack of the |
|
|
|
|
|
|
|
(3) Run a shielded cable from the |
|
|
|
| 3 |
| |
biamp low out jack of the |
|
|
|
|
| ||
its power amp in jack. |
|
|
|
|
|
|
|
(4) Run a speaker cable from the |
|
|
|
|
|
| |
speaker out jack of the | direct | 4 |
|
|
|
| |
direct in jack of the |
| in |
|
|
|
|
|
|
|
|
|
|
|
| |
Adjust the Crossover Frequency and |
|
| 2 | 4 |
|
| |
Balance controls for the best sound. |
|
|
|
|
|
|
TO |
| TO |
|
6