Installation

Electrical Requirements

For your own safety, we recommend that your cooker is installed by a competent person such as one who is registered with NICEIC (National Inspection Council for Electrical Installation Contracting). The cooker should be installed in accordance with the latest edition of the IEE Regulations.

Warning: This appliance must be earthed.

Electrical Connections

The installer must check that the voltage shown at the rating plate corresponds with the house electricity supply.

The cooker must be supplied via a suitable double pole isolating switch, having a contact separation of at least 3mm in all poles placed in a readily accessible position adjacent to the cooker.

If the cooker is to be wired into a connector unit, this may be positioned behind the cooker providing the following requirements are met:

i)The connector unit must not project from the wall more than 25mm.

ii)The top of the connector must not be more than 130mm above floor level.

Remove the terminal cover at the rear base of the cooker. Pass the cable through the cable clamp and connect to the appropriate terminals provided.

Allow sufficient cable for any future servicing.

Tighten the screws on the cable clamp and replace the cover.

Make main connections in the connector unit or cooker control unit.

This appliance conforms to B.S. EN 55014 regarding suppression of Radio and Television reception interference.

Adouble Pole control switch having a minimum rating of 32 amps should be used to feed the cooker using a suitably rated cable.

Where a hob is fitted adjacent to or over the cooker, a 45 amp Double Pole control switch should be used to feed both units via separate suitably rated cables.

We recommend a minimum of 4mm2 PVC insulated twin and earth cable conforming to B.S. 6004 for connection of each appliance.

Where a hob is fitted above the cooker the cable connecting the hob to the cooker control unit must be of 2.5mm2 85o C heat resistant cable to BS6141 table 15

In all cases adhere to routing details (see fig. 4).

This appliance must not be installed over any other appliance that generates heat such as a plinth heater

Note: Due to many different types of installation, a mains cable is not supplied with this product. The installer will fit the correct type and length of cable.

33

Page 32 Page 34
Page 33
Image 33
Creda R430E Installation, Electrical Requirements, Electrical Connections, All cases adhere to routing details see fig
Page 32 Page 34

N230E, E430E, R430E specifications

The Creda R430E, E430E, and N230E models represent a significant advancement in the realm of electric heating appliances, combining efficiency, user-friendliness, and modern aesthetics. These models are tailored to meet a variety of heating needs, making them suitable for both residential and light commercial applications.

One of the standout features of the Creda R430E, E430E, and N230E is their energy efficiency. These models are designed with advanced heating technologies that minimize energy consumption while maximizing heat output. This not only leads to lower energy bills for the user but also contributes to an environmentally friendly heating solution.

Each model is equipped with a built-in thermostat, allowing users to set their desired temperature with precision. This feature enhances user comfort, ensuring that spaces are heated to the desired levels without unnecessary energy waste. Additionally, these appliances incorporate programmable timers, enabling users to schedule heating in advance, further promoting energy efficiency and user convenience.

The Creda R430E, in particular, is known for its robust build quality and durability. Its design incorporates safety features such as overheat protection and a sturdy casing, ensuring that the unit remains safe to operate, even in busy environments. The E430E and N230E models also share this emphasis on safety, making them reliable choices for homes and other settings.

Another noteworthy characteristic of these models is their whisper-quiet operation. Unlike traditional heating systems, the Creda appliances operate silently, making them ideal for bedrooms, offices, and other quiet spaces. This attribute enhances the overall user experience, as there is no distracting noise associated with heating.

In terms of aesthetics, both the R430E and E430E models boast a sleek and modern design that effortlessly blends into any décor. Their compact size allows for flexible installation options, whether mounted on a wall or placed on the floor, ensuring that users can optimize their space.

Overall, the Creda R430E, E430E, and N230E models showcase a perfect balance of performance, safety, and aesthetic appeal. They represent a solid investment for individuals seeking reliable and efficient heating solutions, making them a preferred choice among homeowners and businesses alike.
Top Page Image Contents