18
18TABLE 4: PERMISSIBLE VENT SYSTEMS AND PRINCIPLE VENT COMPONENTS
MANUFACTURER VENT SYSTEM SIZE CONDENSATE
TRAP WALL
THIMBLES HORIZONTAL
TERMINATION VERTICAL
TERMINATION
HEAT FAB
SAF-T VENT
EZ SEAL
39321
(NOTE 3)
7393GC
7393GCS
5391CI
ELBOW: 7314TERM
TEE: 7390TEE 5300CI
49421
(NOTE 3)
7493GC
7493GCS
5491CI
ELBOW: 7414TERM
TEE: 7490TEE 5400CI
SAF-T VENT SC
3SC03DRN
(NOTE 3) SC03FS
SC03FSA
ELBOW (NOTE 5):
SC03HT + 7314TERM
TEE (NOTE 5):
SC03HT + 7390TEE
5300CI + SC03VT
(NOTE 6)
4SC04DRN
(NOTE 3) SC04FS
SC04FSA
ELBOW (NOTE 5):
SC04HT + 7414TERM
TEE (NOTE 5):
SC04HT + 7490TEE
5400CI
+ SC04VT
(NOTE 6)
PROTECH
SYSTEMS
INC.
FASNSEAL
3 FSHDT3 FSWT3 ELBOW: FSELB9003 + FSBS3
TEE: FSTT3 FSRC3
4FSHDT4
OR FSCD4
(NOTE 4) FSWT4 ELBOW: FSELB9004 + FSBS4
TEE: FSTT4 FSRC4
FASNSEAL W2
3W2-T3
+W2-DF3 W2-WT3 ELBOW: FSA-SWDW3
+ FSELB9003 + FSBS3
TEE: FSA-SWDW3 + FSTT3 W2-RC3
4W2-T4
+ W2-DF4 W2-WT4 ELBOW: FSA-DWSW4
+ FSELB9004 + FSBS4
TEE: FSA-SWDW4 + FSTT4 W2-RC4
Z-FLEX SVE
SERIES III
(“Z-VENT III”)
3 SVEDWCF03 2SVSWTEF03 ELBOW: 2SVSTEX0390
TEE: 2SVSTTF03 2SVSRCF03
4 SVEDWCF04 2SVSWTEF04 ELBOW:
2SVEEWCF0490 + 2SVSTPF
TEE: 2SVSTTF04 2SVSRCF04
METAL-FAB CORR/GUARD
3 CGSWDS(3”) CGSWWPK(3”) ELBOW: CGSW90LTM(3”)
TEE: CGSWTTM(3”) CGSWC(3”)
4 CGSWDS(4”) CGSWWPK(4”) ELBOW: CGSW90LTM(4”)
TEE: CGSWTTM(4”) CGSWC(4”)
NOTES:1) See vent system manufacturer’s literature for other part numbers that are required such as straight pipe, elbows, fi restops and vent supports.2) In addition to terminals shown, Crown coaxial terminals may be used in some cases. See Table 3 for applications and Crown part numbers.3) All Heat Fab condensate traps shown may be installed in vertical or horizontal run.4) Protech FSCD4 condensate trap may be installed in a vertical or horizontal run. All other Protech traps must be installed in a horizontal run only. 5) Heat Fab Saf-T Vent SC may not be used for horizontal coaxial venting - a separate air inlet pipe must be provided for hori-zontal direct vent systems. SC03HT or SC04HT adapters are used to adapt from SC pipe to terminal. Use of SC pipe in horizon-tal systems does allow for reduced clearances to combustibles in some applications. See Table 2. 6) Heat Fab SC03VT or SC04VT adapters are required on any vertical vent system using Saf-T Vent SC even when combustion air is obtained through a separate pipe or from the boiler room. 7) Metal-Fab CGSWDS condensate traps may only be installed in a horizontal run.