Note: If you wish to move the mower by pushing, you must release the dynamic brak- ing. Locate the levers at the rear of the mower. Pull both levers out and lock in position. After pushing the mower to the desired location, return both levers to the operating position (See photo below).

Hydro Release Levers

When the mower is parked with the engine running and the steering levers opened out in the neutral position, the parking brakes should be applied. The parking brakes are drum-type brakes mounted on each traction wheel.They are both engaged by the same operating lever.

1.Adjustments: The parking brake handle is an overcenter lever that should engage with moderate force.

Note: To increase parking brake capacity tighten the brake rods going back to the brake arms equally. Tighten rods one full turn and check parking capacity. Repeat Step.

To adjust either brake individually, disconnect the brake rod from the brake arm by removing the cotter pin from the clevis pin and pulling the clevis pin from the brake clevis. Loosen the hex nut and turn the brake clevis in a clockwise direction one full turn looking down the brake rod. This will tighten the brake about .040 inch. Tighten the hex nut and reassemble the brake clevis to the brake shaft assembly. Normally, both brakes should be adjusted and equal amount.

2.Repair: The mower is equipped with internal wet drum brakes and will not normally require maintenance. If they are not working properly, please contact your service center.If thery are not working properly contact your cub cadet service dealer

F.Hydraulic System

1.Hoses: Check the hoses from the hydraulic oil tank to the oil filter to the hydraulic lines daily for leaks or abrasion and replace any

damaged hoses. Make certain there are no kinks or twists in any hose.

2.Hydraulic Oil Tank and Filter:

Note: Change the hydraulic oil and the oil filter after the first 50 hours of operation and every 500 hours thereafter.

To drain the hydraulic oil tank, place a 2 gallon drain pan under the drain plug on the bottom of the hydraulic oil tank. Remove the drain plug, drain the tank, then replace the plug. Place the drain pan under the filter and remove the filter by unscrewing in a counterclockwise direction. The filter will be full of oil, so empty it into the drain pan. You don’t have to drain the rest of the hydraulic system. Fill the replacement filter with a good grade of 20W-50 oil and lubricate the sealing surface. Screw the filter onto the filter base until it seats and then another one-half turn to seal.

Note: Always wipe off the hydraulic tank fill

cap and the area around it before removing the cap to prevent dirt from contaminating the oil.

Remove the fill cap and fill the tank with the same 20W-50 oil selected for the filter until the oil level is up to the level of the second hole in the fill tube. Leave this air space for expansion. Start the engine and let it run at idle for about five minutes. Check the filter for leaks. Idling the engine and the pumps in this way will purge any air from the system. Shut off the engine and recheck the oil level in the tank. Top-off if necessary until the oil level is up to the second hole n the fill tube.

Note: After unit is up to operating tempera- ture, turn off engine and re-check hydraulic oil. If oil appears foamy or contains excessive air bubbles, DO NOT OPERATE UNIT. Contact Cub Cadet Service Dealer.

3.Hydrostatic Transmissions and motors: The pumps are the hardest-working compo- nents in the hydraulic system. They are in operation all the time the engine is running. Because of extremely close tolerances, wear is an important factor in their life. Contami- nants in the hydraulic oil and cavitation does the greatest harm to the pumps. Cavitation is a blockage in the supply lines that produces a partial vacuum causing violent bubbling in the hydraulic oil in the pump.

Check the two suction hoses (the hoses con- nected to the filter) daily before starting the engine. Look for a flattened condition or any leaks and repair or replace as necessary. A flattened or leakng suction hose will permit

20

Page 19 Page 21
Page 20
Image 20
Cub Cadet 18HP service manual Hydraulic System, Hydraulic Oil Tank and Filter
Page 19 Page 21

18HP specifications

The Cub Cadet 18HP is a robust and versatile garden tractor designed to meet the demanding needs of homeowners and landscaping professionals alike. This machine packs a powerful engine, advanced features, and user-friendly technologies that make lawn care and garden maintenance an efficient and enjoyable experience.

At the heart of the Cub Cadet 18HP is a high-performance 18 horsepower Kohler engine. This engine is engineered for reliability and effectiveness in a variety of mowing and hauling tasks. With a smooth and powerful operation, it efficiently tackles tough grass and uneven terrain, ensuring a pristine cut every time. The engine's two-cylinder design contributes to reduced vibrations and improved fuel efficiency, making it not only powerful but also economical to operate.

One of the standout features of the Cub Cadet 18HP is its innovative Cub Cadet signature cutting deck. The tractor is equipped with a 42-inch or 50-inch cutting deck, meticulously designed for superior grass cutting and discharge. This cutting system features twin blades that deliver an exceptional cut quality while reducing clumping and providing optimal air flow. The adjustable cutting height allows users to customize the grass length to their preference, ensuring a well-manicured lawn.

Incorporating advancements in technology, the Cub Cadet 18HP is equipped with a hydrostatic transmission. This feature provides smooth and effortless speed control, allowing homeowners to easily navigate around their properties without the need for constant gear shifting. Whether tackling inclines or navigating tight spaces, the hydrostatic transmission ensures maximum control and maneuverability.

Comfort is also a priority with the Cub Cadet 18HP. The tractor boasts a spacious, ergonomically designed seat that offers excellent support during extended use. Additionally, the easy-to-reach controls and cup holder enhance the overall user experience. Built-in headlights provide visibility for early morning or late evening mowing sessions, ensuring that users can work with ease at any time of day.

For those looking to expand the functionality of their tractor, the Cub Cadet 18HP supports a variety of attachments. From baggers to snow blades and tillers, this versatility allows users to tackle different tasks throughout the seasons, making it a true all-in-one gardening solution.

In summary, the Cub Cadet 18HP stands out in its category for its powerful engine, innovative cutting deck, hydrostatic transmission, and user-centric design. This garden tractor promises durability and efficiency, making it an indispensable tool for anyone serious about lawn care. Whether you are a weekend warrior or a landscaping professional, the Cub Cadet 18HP is built to handle the job with ease and reliability.
Top Page Image Contents