Performance Adjustments

A. High Speed Tracking Adjustment

If mower tracks to one side with both lap bars in fully forward position:

1.Check air pressure in all four tires:

a.Pressure should be within specified ranges and balanced side-to-side.

b.Rear tires 8-10 psi. recommended (20 psi MAX.)

c.Front tires 20-25 psi. recommended (28 psi MAX.

2.Check hydraulic fluid level (Ref. Engine owner’s manual)

3.Verify that the mower does not creep when the engine is running, the lap bars are in the neutral position and the parking brake is released. (Refer to section E-3 on page 22 of this manual if this condition exists).

4.Recheck the tracking after any adjustments based on the above.

5.If uneven tracking persists, adjust as follows. (see Fig. 10)

a.Unit tracks to the RIGHT, adjust Left lap bar stop bolt to make it longer.

b.Unit tracks to the LEFT, adjust Right lap bar stop bolt to make it longer.

6.Re-check the tracking and make any fine tun- ing adjustments to the lap bar stop bolts as required.

Note: If stop bolt is adjusted too far, track-

ing problem will change sides. Make the fine tuning adjustments by shortening the same bolt.

Figure. 11

Lap Bar Stop Bolt

B. Enginge RPM Check and Adjustment

Description

High RPM Spec.

Low RPM Spec.

 

 

 

29 Hp Kawasaki

3700 +/-50

1550 +/-100

 

 

 

NOTE: RPM Specs. are for free running engines under no load.

1.Verify that the lap bars are in the neutral posi- tion, the parking brake is on, and the PTO drive is disengaged.

2.Start the mower and let it run at approximately half throttle for 3-5 minutes to bring the engine up to operating temperature.

3.Locate the Hour Meter/Tachometer/ Service Minder display on the right hand operator con- trol panel. (see Fig.1 on page 10 of the man- ual) This display defaults to Tachometer mode when engine is running.

4.Move the throttle lever to the high speed posi- tion and note the RPM reading on the display.

5.Move the throttle lever back to the low speed position and again note the displayed RPM’s.

6.Compare these noted RPM readings to the specifications in Table 1, for the engine that is on your mower.

7.If the readings do not correspond to the ranges in the table, refer to the engine owner’s manual for the proper adjustment pro- cedures.

8.If adjustments per the engine operator’s man- ual do not result in proper RPM readings, con- tact your service technician.

9.Note: The throttle cable sheath may shrink or slip over time, changing the relationship between the throttle lever on the left hand operator control panel and the throttle arm on the engine. To readjust the throttle cable:

a.Make sure the engine is off, place lap bars in the neutral position, set the parking brake, and disconnect and ground both of the spark plug wires.

b.Locate and loosen the cable clamp on the engine throttle plate.

c.Place the operator’s throttle lever to the high speed position and then slide the cable through the clamp until the throttle arm is in the full throttle position. (Ref. Engine owner’s manual)

d.Tighten the cable clamp.

e.Move the operator’s throttle lever between high and low speed and verify that the engine throttle arm also moves through it’s full range of motion.

f.Repeat as required to obtain proper throt- tle adjustment.

g.Verify proper throttle adjustment by check- ing RPM readings as outlined above.

27

Page 26 Page 28
Page 27
Image 27
Cub Cadet 53AJ8CT6050 service manual High Speed Tracking Adjustment, Enginge RPM Check and Adjustment
Page 26 Page 28

53AJ8CT6050 specifications

The Cub Cadet 53AJ8CT6050 is a riding lawn mower that combines power, precision, and advanced technology to provide an exceptional mowing experience. Designed for homeowners who demand top performance and reliability, this model stands out in the competitive landscape of outdoor power equipment.

One of the key features of the Cub Cadet 53AJ8CT6050 is its powerful engine. Equipped with a robust 18.5 horsepower Kohler engine, it delivers ample torque and speed to tackle a variety of terrains. This ensures a smooth mow even in challenging conditions, making it ideal for both flat lawns and hilly landscapes. The engine is paired with a smooth hydrostatic transmission, allowing for effortless gear changes without the need for shifting.

Another notable characteristic is its innovative cutting system. The mower features a 50-inch cutting deck, designed to cover more ground in less time. The deck's adjustable cutting height, ranging from 1.5 to 4 inches, allows users to customize their mowing experience, ensuring a pristine lawn regardless of grass type. The twin-blade design enhances the mowing efficiency, providing even cutting and superior grass mulching, which can help return vital nutrients back to the soil.

The Cub Cadet 53AJ8CT6050 also emphasizes user comfort and ease of operation. It features a plush, ergonomic operator station with a high-back seat and armrests, allowing for extended use without discomfort. The steering wheel's design enhances maneuverability, making it easier for operators to navigate tight spots and obstacles in their yard.

In terms of technology, the mower incorporates advanced features such as the SmartJet deck washing system, which allows for quick and hassle-free cleaning of the cutting deck after use. This not only maintains the mower's performance but also prolongs its lifespan by preventing grass buildup.

Additionally, the Cub Cadet 53AJ8CT6050 is compatible with a range of attachments, further enhancing its utility. Owners can add accessories such as baggers, carts, and plows, turning the mower into a versatile tool for various lawn and garden tasks.

Overall, the Cub Cadet 53AJ8CT6050 is a well-rounded riding mower that blends performance, comfort, and technology. Whether you have a small suburban lawn or a sprawling estate, this mower is equipped to meet your landscaping needs effectively. With its robust construction and thoughtful features, it's a reliable choice for discerning homeowners looking to invest in quality outdoor equipment.
Top Page Image Contents