SECTION 2: ASSEMBLING YOUR SNOW THROWER

NOTE: Any reference in this manual to the left or right side of the snow thrower is observed from the operator’s position.

Unpacking

•Remove staples from the top sides and ends of the shipping crate.

•Set panel aside to avoid tire punctures or personal injury.

•Remove and discard plastic bag that covers unit.

•Remove any loose parts included with unit (i.e., Operator’s Manual, etc).

•Roll unit out of crate.

Loose Parts

The augers are secured to the auger shaft with two shear bolts and hex lock nuts. If you hit a foreign object or ice jam, the snow thrower is designed so that the bolts may shear. Two replacement shear bolts and nuts are provided for your convenience. Store in a safe place until needed. See Figure 1.

Shear Bolts

 

Hex Lock

 

 

 

Nuts

Figure 1

Assembly

Disconnect the spark plug wire and ground it against the engine to prevent unintended starting.

•Remove the lower two plastic wing nuts, cupped washers and carriage bolts from each side of the lower handle. See Figure 2.

Lower

Handle

Handle

Panel

 

Upper Handle

 

Wing Nuts,

 

Washers, & Bolts

Figure 2

•Raise the upper handle assembly until it locks over the lower handle.

•Look at lower rear of snow thrower frame to be sure both cables are aligned with cable roller guides. See Figure 3.

Cable Roller

Guides

Figure 3

•Secure the upper handle and lower handle with the two plastic wing knobs, cupped washers and carriage bolts previously removed and tighten the upper two plastic wing nuts. See Figure 4.

Upper

Shift Rod

Shift Rod

Connector

Lower

Shift Rod

Wing Nuts

Figure 4

•Slide the shift rod connector down over the end of the lower shift rod. Tap the connector until it locks on the lower shift rod. See Figure 4.

NOTE: If the connector is not properly assembled, the shift rod will pivot and you will not be able to shift gears or change directions.

•If not already attached, slip the cables that run from the handle panel to the chute into the cable guide on top of the engine. See Figure 5.

5

Page 4 Page 6
Page 5
Image 5
Cub Cadet 826 4x4 manual Assembling Your Snow Thrower, Unpacking, Loose Parts, Assembly, Shear Bolts Hex Lock Nuts
Page 4 Page 6

826 4x4 specifications

The Cub Cadet 826 4x4 is a powerful and versatile snow blower designed for homeowners who face harsh winter conditions. It combines robust engineering with user-friendly features, making snow removal a more manageable task. This machine is equipped with a 26-inch clearing width, allowing it to tackle significant snow accumulations efficiently.

One of the standout features of the Cub Cadet 826 4x4 is its 4-wheel drive capability. This ensures that users can navigate snowy terrain with ease, providing enhanced traction and stability on slopes and uneven surfaces. The hydrostatic transmission allows for smooth speed adjustments and effortless maneuvering. This feature is particularly beneficial when operating in tight corners or delicate areas where precision is essential.

The snow blower is powered by a reliable 2-stage engine, which generates ample power for heavy-duty snow clearing. The two-stage system means that after the auger gathers snow, it is thrown out of the discharge chute with significant force, making it ideal for dealing with packed snow and deep drifts. The adjustable chute also allows users to direct the snow far away from the cleared area, preventing it from being blown back onto already cleared surfaces.

In terms of comfort, the Cub Cadet 826 4x4 prioritizes ease of use. It features heated hand grips that keep operators warm during extended periods of cold weather. Moreover, the large, easy-to-operate controls are designed to minimize fatigue, allowing users to focus on the job at hand. The machine’s generous fuel tank capacity ensures longer operation times without frequent refueling, adding to its convenience.

Durability is another key characteristic of the Cub Cadet 826 4x4. Built with high-grade materials, it is designed to withstand the rigors of winter use. The high-impact, snow-resistant construction ensures longevity, making it a smart investment for homeowners looking to manage snow effectively year after year.

In summary, the Cub Cadet 826 4x4 is an exceptional snow blower that combines power, technology, and user comfort. Its robust features make it suitable for tackling even the most challenging winter conditions, ensuring users can clear their paths quickly and efficiently. With its combination of durability, performance, and ease of use, the Cub Cadet 826 4x4 is a top choice for anyone looking to conquer snow this winter.
Top Page Image Contents