Maintenance (continued)

0.025 inch

(0.655 mm)

Fig. 6-15

Replacing the Spark Plug

Use a Champion RCJ6Y spark plug (or equivalent). The correct air gap is 0.025 inch (0.655 mm). Remove the plug after every 25 hours of operation and check its condition.

1.Stop the engine and allow it to cool. Grasp the plug wire firmly and pull the cap from the spark plug.

2.Clean dirt from around the spark plug. Remove the spark plug from the cylinder head by turning a 5/8 inch socket counterclockwise.

3.Replace cracked, fouled or dirty spark plug. Set the air gap at 0.025 inch (0.655 mm) using a feeler gauge (Fig. 6-15).

Do not sand blast, scrape, or clean electrodes. Grit in the engine could damage the cylinder.

4.Install a correctly-gapped spark plug in the cylinder head. Tighten by turning the 5/8 inch socket clockwise until snug.

If using a torque wrench torque to:

110-120 in.•lb. (12.3-13.5 N•m). Do not over tighten.Cleaning

To avoid serious personal injury, always turn your trimmer off and allow it to cool before you clean or do any maintenance on it.

Use a small brush to clean off the outside of the unit. Do not use strong detergents. Household cleaners that contain aromatic oils such as pine and lemon, and solvents such as kerosene, can damage plastic housing or handle. Wipe off any moisture with a soft cloth.

Storage

•Never store the unit with fuel in the tank where fumes may reach an open flame or spark.

•Allow the engine to cool before storing.

•Store the unit locked up to prevent unauthorized use or damage.

•Store the unit in a dry, well-ventilated area.

•Store the unit out of the reach of children.

Long Term Storage

If the unit will be stored for an extended time, use the following storage procedure:

1.Drain all fuel from the fuel tank into a container with the same 2-cycle fuel mixture. Do not use fuel that has been stored for more than 60 days. Dispose of the old fuel/oil mix in accordance to Federal, State and Local regulations.

2.Start the engine and allow it to run until it stalls. This ensures that all fuel has been drained from the carburetor.

3.Allow the engine to cool. Remove the spark plug and put 1 oz. (30 ml) of any high quality motor oil or

2-cycle oil into the cylinder. Pull the starter rope slowly to distribute the oil. Reinstall the spark plug.

NOTE: Remove the spark plug and drain all of the oil from the cylinder before attempting to start the trimmer after storage.

4.Thoroughly clean the unit and inspect it for any loose or damaged parts. Repair or replace damaged parts and tighten loose screws, nuts or bolts. The unit is ready for storage.

Transporting

•Allow the engine to cool before transporting.

•Drain fuel from unit.

•Tighten fuel cap before transporting.

•Secure the unit while transporting.

Accessories / Replacement Parts

2-Cycle Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .180965

Spark Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181765

Spark Arrestor . . . . . . . . . . . . . . . . . . . . . . . . . . .181696

Replacement Line Cartridge . . . . . . . . . . . . . . 753-1160

Inner Reel Spring . . . . . . . . . . . . . . . . . . . . . . . . 610636

Bump Head Knob Assembly . . . . . . . . . . . . . . . . 180814

Brushcutter Accessory Kit . . . . . . . . . . . 41AM079G100

Fuel Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .181612

Shoulder Strap . . . . . . . . . . . . . . . . . . . . . . . . . . 682075

17