SECTION 8: SERVICE

Tires

WARNING: Never exceed the maximum inflation pressure shown on the sidewall of the tire.

The recommended operating tire pressure is approximately 10 psi for the rear tires and 14 psi for the front tires.

Refer to the tire sidewall for exact tire manufacturer’s recommended or maximum psi. Do not overinflate. Uneven tire pressure could cause the cutting deck to mow unevenly.

Fuse

A fuse is installed in your tractor’s wiring harness to protect the tractor’s electrical system from damage caused by excessive amperage.

If the electrical system does not function, or your tractor’s engine will not crank, first check to be certain that the fuse has not blown.

It can be found under the hood mounted behind the top of the dash panel on the support bar.

IMPORTANT: Always use a fuse with the same amperage capacity for replacement.

WARNING: Before servicing, repairing, or inspecting, always disengage PTO, set parking brake, stop engine and remove key to prevent unintended starting.

Cutting Blades

WARNING: Be sure to shut the engine off, remove ignition key, disconnect the spark plug wire(s) and ground against the engine to prevent unintended starting before removing the cutting blade(s) for sharpening or replacement. Protect your hands by using heavy gloves when grasping the blade.

WARNING: Periodically inspect the blade adapter and/or spindle for cracks or damage, especially if you strike a foreign object. Replace immediately if damaged.

The blades may be removed as follows.

•Remove the deck from beneath the tractor, (refer to Cutting Deck Removal on page 26) then gently flip the deck over to expose its underside.

•Place a block of wood between the center deck housing baffle and the cutting blade to act as a stabilizer. See Figure 21.

Hex Flange Nut

Wood Block

Spindle Assembly

Figure 21

•Use a 1-1/8" wrench to remove the hex flange nut

that secures the blade to the spindle assembly. See Figure 21.

To properly sharpen the cutting blades, remove equal amounts of metal from both ends of the blades along the cutting edges, parallel to the trailing edge, at a 25° to 30° angle.

IMPORTANT: If the cutting edge of the blade has already been sharpened, or if any metal separation is present, replace the blades with new ones.

It is important that each cutting blade edge be ground equally to maintain proper blade balance. A poorly balanced blade will cause excessive vibration and may cause damage to the tractor and result in personal injury.

The blade can be tested by balancing it on a round shaft screwdriver. Grind metal from the heavy side until it balances evenly.

IMPORTANT:When replacing the blade, be sure to install the blade with the side of the blade marked ‘‘Bottom’’ (or with a part number stamped in it) facing the ground when the mower is in the operating position.

IMPORTANT:Use a torque wrench to tighten the blade spindle hex flange nut to between 70 lbs-ft and 90 lbs-ft.

25

Page 24 Page 26
Page 25
Image 25
Cub Cadet LT1046, LT1050, LT1045 manual Service, Tires, Fuse, Cutting Blades
Page 24 Page 26

LT1046, LT1050, LT1045 specifications

Cub Cadet is renowned for producing high-quality lawn tractors that cater to both residential and commercial needs. Among their popular models is the Cub Cadet LT series, particularly the LT1045, LT1050, and LT1046, which are designed for optimum performance and user comfort.

The Cub Cadet LT1045 is powered by a robust 19 horsepower Kohler engine, providing ample power for various lawn care tasks. Its hydrostatic transmission offers smooth and effortless maneuverability, allowing users to easily navigate their lawns without the need for gear shifting. Equipped with a 42-inch cutting deck, the LT1045 is ideal for medium-sized yards. Its adjustable cutting height ranges from 1 to 4 inches, giving users flexibility to achieve their desired grass length. Moreover, the LT1045 features a comfortable, ergonomic seat that minimizes fatigue during prolonged use.

Moving up the lineup, the LT1046 comes with a slightly more powerful 21 horsepower engine, suited for larger lawn areas. It also features a 46-inch cutting deck which enhances efficiency by covering more ground in a single pass. The LT1046 has a dual-blade system, improving grass cutting and reducing clumping, which can be beneficial for maintaining a neat appearance. Similar to the LT1045, this model incorporates the same hydrostatic transmission, making it user-friendly.

The Cub Cadet LT1050 is a step above the previous models, with an impressive 23 horsepower engine. This powerful engine is capable of handling tougher terrains and taller grass, making it a perfect choice for larger plots or uneven ground. The LT1050 features a 50-inch cutting deck, which significantly reduces mowing time. Furthermore, it boasts advanced cutting technologies such as SmartJet deck wash and a reinforced cutting deck, ensuring durability and ease of maintenance.

All these models exemplify Cub Cadet's emphasis on comfort and convenience; they are equipped with a high-back seat and easy-to-use controls, catering to users of all experience levels. Some models also include features like LED headlights for early morning or late evening mowing.

In summary, the Cub Cadet LT1045, LT1046, and LT1050 offer a variety of features designed for efficiency, comfort, and durability. With advanced engineering and practical technologies, these models are excellent choices for anyone looking to maintain their lawn with ease and precision.
Top Page Image Contents