OPERATING INSTRUCTIONS

CLEANING AND STORAGE

ADJUSTING THE TRIMMER LINE

The trimmer line wears down and becomes shorter with use. This unit is equipped with an Automatic Line Advancement cutting head. Line is automatically extended each time the motor starts.

If the line becomes too short:

1.Stop the motor. See Starting and Stopping Instructions.

2.Wait two seconds and then restart the motor.

3.Repeat this process until the line length reaches the line cutting blade on the cutting head shield.

If the line does not automatically advance, the trimming line may be tangled or empty. Refer to the Maintenance section of this manual.

NOTE: DO NOT bump the cutting head; this will damage the unit and void the warranty.

The trimming line can also be extended manually by lightly pressing the manual line release button (Fig. 14) and pulling the trimming line. When doing so, always make sure the motor is off and the battery is removed from the unit.

The life of your cutting line is dependent upon:

• Following the trimming techniques previously explained

• What vegetation is cut

• Where the vegetation is cut.

For example, the line will wear faster when trimming against a foundation wall as opposed to trimming around a tree.

Decorative Trimming

Decorative trimming is the act of removing all vegetation from around trees, posts, fences, etc. To accomplish it, rotate the whole unit so that the cutting

attachment is at a 30˚ angle to the ground (Fig. 13).

 

Fig. 13

 

 

 

MAINTENANCE AND REPAIR INSTRUCTIONS

WARNING: Before inspecting, cleaning, or servicing the

Cutting

unit, stop the motor, wait for all moving parts to stop and

Head

remove the battery. Failure to follow these instructions can

 

result in serious personal injury or property damage.

 

LINE INSTALLATION

 

Only use original equipment manufacturer replacement line (up to 0.080 inch (2.03

 

mm) diameter). Line other than the specified may make the motor overheat or fail.

 

WARNING: Never use metal-reinforced line, wire, chain or

Manual Line

Release button

rope. These can break off and become dangerous projectiles.

 

There are two methods to replace the trimming line:

Tabs

 

• Wind the inner reel with new line

Fig. 14

•Install a prewound inner reel

Winding the Existing Inner Reel

Spool

Cutting Head

1. Remove the cutting head cover by pressing in both tabs that are visible on

Cover

either side or the cutting head (Fig. 14).

 

 

2. Remove the inner reel from the outer spool (Fig. 15).

3.

Remove any old line from the inner reel and use a clean cloth to wipe the

Outer

Spool

 

inner surface of the outer spool.

 

 

NOTE:

Use a clean cloth to clean the inner reel, spring, shaft, and inner

 

 

 

surface of the outer spool.

 

4.

Take approximately 12 feet (3.6 m) of new trimming line and insert one end of

 

 

the line into the hole at the top of the inner reel (Fig. 16).

 

5.

Wind the line, in even and tight layers, onto the reel (Fig. 16). Wind the line in

Eyelet

 

the direction indicated on the inner reel.

 

 

NOTE:

Failure to wind the line in the direction indicated will cause the cutting

Fig. 15

 

 

head to operate incorrectly.

 

 

 

6.Insert the end of the line into one of the holding slots (Fig. 16).

7.Insert the end of the line through the eyelet in the outer spool (Fig. 15).

8.Place the inner reel inside the outer spool.

9.

Hold the inner reel in place, grasp the line end and pull firmly to release the

 

 

line from the holding slot in the inner reel.

 

10.

Install the cutting head cover over the inner reel. Align the tabs on the cover

 

 

with the slots in the outer spool and press the cover down evenly until it

 

 

snaps into place (Fig. 15).

 

NOTE: Make sure the cutting head cover tabs snap into place or the inner reel

 

 

will come out during operation.

 

Installing a prewound reel

 

Always use genuine replacement line. Using larger line than specified may make

 

the motor overheat or fail.

 

1.

Remove the cutting head cover by pressing in on both of the cutting head

Fig. 16

cover tabs that are visible on either side of the outer spool (Fig. 14).

2.Remove the old inner reel from the outer spool.

3.Use a clean cloth to wipe the inner surface of the outer spool.

4.Insert the end of the line of the pre-wound reel through the eyelet in the outer spool (Fig. 15).

5.Place the inner reel inside the outer spool (Fig. 15).

6.Hold the inner reel in place, grasp the line end and pull firmly to release the line from the holding slot in the inner reel.

7.Install the cutting head cover over the inner reel. Align the tabs on the cover with the slots in the outer spool and press the cover down evenly until it snaps into place.

NOTE: Make sure the cutting head cover tabs snap into place or the inner reel will come out during operation.

CHARGER MAINTENANCE

•Keep the charger clean and clear of debris. Do not allow foreign material into the recessed cavity or on the contacts.

•Wipe with a dry cloth. Do not use solvents, water or place in wet conditions.

•Always unplug the charger when not in use.

•The battery pack may be stored in the charger. However, it is recommended to disconnect the charger from the power source.

•To ensure safety and reliability, all repairs should be performed by a qualified service technician.

•Check that the charger contacts have not been shorted by debris or foreign material.

•Keep the charger and battery pack in an area that is between 65 and 75˚ F (18 and 24˚ C).

ENVIRONMENTALLY SAFE BATTERY DISPOSAL

The following toxic and corrosive materials are used in this units battery pack:

LITHIUM-ION, a toxic material.

WARNING: All toxic materials must be disposed of in a specified manner to prevent contamination of the environment. Before disposing of damaged or worn out lithium-ion battery packs, contact your local waste disposal agency for information and specific instructions. Take batteries to a local recycling and or disposal center, certified for lithium-ion battery disposal.

WARNING: Do not use the battery pack if there are cracks or if it breaks, regardless if there is leakage or not. Replace with a new battery pack. DO NOT ATTEMPT TO REPAIR! As this may cause severe personal injury due to explosion or electrical shock.

To avoid damage to the environment:

•DO NOT attempt to remove or destroy any of the battery pack components.

•DO NOT attempt to open the battery pack.

•DO NOT place the battery pack in the regular household trash.

•DO NOT incinerate.

•DO NOT place them where they will become part of any waste landfill or municipal solid waste stream.

•Cover the battery terminals with heavy-duty adhesive tape.

•If a leak develops, the released electrolytes are corrosive and toxic. DO NOT get the solution in your eyes or on your skin, and do not swallow it.

•Dispose of the battery pack in accordance with local, state and federal regulations.

WARNING: Do not let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in contact with plastic parts. These chemicals may damage, weaken and destroy plastic, which may result in serious personal injury.

WARNING: To avoid risk of fire, electric shock or electrocution: DO NOT use a damp cloth or detergent on the battery or battery charger. Wipe the outside with a dry, soft cloth.

CLEANING INSTRUCTIONS

1.Stop the motor and wait for all moving parts to stop.

2.Remove the battery from the unit.

3.Wipe the unit down with a damp cloth. Do not douse the unit with water. Do not use solvents or strong detergents.

4.Scrape the guard and spool area to remove dried clippings and mud.

5.Brush or blow dust, debris and grass clippings out of the air vents. Keep them free or obstructions

STORAGE INSTRUCTIONS

1.Follow the Cleaning Instructions listed above.

2.Store the unit indoors in a dry, high and/or locked location, out of the reach of children and other unauthorized persons.

TROUBLESHOOTING

 

 

 

 

 

THE MOTOR OPERATES SLOWLY OR WILL NOT OPERATE

 

CAUSE

 

SOLUTION

The battery lacks sufficient charge

 

Charge the battery

 

 

 

THE BATTERY WILL NOT CHARGE

 

CAUSE

 

SOLUTION

There is no power to the charger or battery

 

Check the charger and charging station

The battery has failed

 

Replace the battery

 

 

 

THE CUTTING HEAD WILL NOT ADVANCE LINE

 

 

CAUSE

 

SOLUTION

 

 

 

The cutting head is bound with grass

 

Stop the motor, remove the battery and clean the cutting head

The cutting head is out of line

 

Refill the cutting head with new line

The inner reel is bound up

 

Replace the inner reel

The cutting head is dirty

 

Clean the inner reel and outer spool

The line is welded

 

Disassemble, remove the welded section and rewind the line

The line twisted when it was refilled

 

Disassemble and rewind the line

 

 

 

THE CUTTING HEAD ADVANCES LINE UNCONTROLLABLY

 

CAUSE

 

SOLUTION

The cutting head is broken

 

Replace as needed

 

 

 

NOTE: For maintenance beyond the minor adjustments listed above, or for replacement parts, please call the Customer Support Department at 1-877-282-8684(U.S.) or 1-800-668-1238(Canada).

SPECIFICATIONS

MOTOR*

Motor Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cordless, Battery-powered Motor Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 V Motor Speed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8500 rpm Motor Wire Housing Tube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Aluminum Tube Unit Weight (With battery, cutting head shield and D-handle). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.2 lbs. (3.86 kg.) Cutting Mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Auto Feed Trimming Line Diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . up to 0.080 in (2.03 mm) Cutting Path Diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 in. (30.5 cm)

BATTERY / BATTERY CHARGER*

Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20V Lithium Charge Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Hours Battery Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.24 Lbs. (1.47 kg) Optimum Charging Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32° to 104° F (0° to 40° C) Battery Charger Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 V 60 Hz AC only Battery Charger Output Maximum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 V Battery Charger Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2 Lbs. (0.54 kg)

*All specifications are based on the latest product information available at the time of printing. We reserve the right to make changes at any time without notice.

ACCESSORIES

 

 

 

Model #

Part #

Description

A59 LBTY . . . . . . . . . . . . .

753-06579 . . . . . . .

20V

Lithium-ion Battery

A59LCHGR . . . . . . . . . . . .

753-06580 . . . . . . .

20V

Lithium-ion Battery Charger

4