English

 

9

 

 

 

your third disc. The discs must be centered in the pockets and loaded with the printed sides facing up. If the disc is not properly centered in the pocket, it may move when you close the drawer. This could jam the mechanism or possibly damage the disc, so be sure to load the disc properly.

•After you have loaded up to 3 CDs press the OPEN/CLOSE button (38) to close the drawer. The changer will read the information of the CD that is in the play position. The display will show the total number of tracks and total playing time of the disc.One of the 3 disc indicators will be blinking to show you which disc is in the play position. To begin playback of the disc, simply press the PLAY/PAUSE >II button (27). The changer will search all three pockets until it locates the disc and then playback will begin.

If no discs are found “disc” will blink on the display.

•Playback begins with track 1 of the first disc and continues until the final track on disc 3 has been played. During playback the disc indicator of the disc that is played will flash. When the last track of the last CD has been played, the changer stops and the display will show the total tracks and playing time of the first disc again.

Notes: If the disc is deeply scratched, or too dirty, disc play may not start.

If on improperly centred disc is played, noise can be heard in the mechanism. The use of such discs should be avoided.

IMPORTANT INFORMATION

This compact disc player has built-in error compensation circuits to correct for minor defects in a disc. There are limits, however, to the amount of correction available. In some cases, the CD player may skip some tracks on a disc during disc play. This problem may be cause by defects (such as scratches) in the disc being played, which are too large for the error compensation circuits to handle. If you encounter this problem, check the CD player’s operation as follows, before having the unit serviced: Play a new disc. If the CD player operates normally, the skipping problem is probably due to a defective disc.

TO STOP A CD PART WAY THROUGH

•Press the Stop button (15). Disc play will stop, and the display will show the total number of tracks for the CD.

•To temporarily stop disc Play (Pause mode), press the Play / Pause button (27) . Disc play will pause at the current play position. The PAUSE indication on LCD will appear.

•To resume disc play, press the PLAY / PAUSE button again. The PAUSE indicator will disappear.

TRACK SKIP

 

 

 

 

 

10

 

English

 

 

 

 

 

 

STARTING DISC PLAY FROM THE BEGINNING OFAPARTICULAR TRACK

 

• Press the Forward or Reverse Skip Track buttons UP/DOWN

(30) to select the

desired track. The number of the selected track will be shown on the CD display. Press the Play/Pause button to start play.

TO SKIP TO THE NEXT TRACK ON A DISC

•For example, to skip ahead to the beginning of the next track .

•Press the UP Track button once. Disc play will resume at the beginning of the next track.

The CD player will skip ahead to the next track each time the UP button is pressed. Continuously pressing the UP Track button makes the CD player skip ahead through the disc track by track. Once the beginning of the last track is reached the CD player will advance to the first track again.

TO SKIP BACK TO THE PREVIOUS TRACK ON A DISC

•For example to skip back to the beginning of the previous track.

• Press the DOWN button twice. If this button is pressed in the middle of a track, the CD player will skip back to the beginning of that track. To make it skip back to the previous track press the DOWN Button twice.

Continuously pressing the DOWN button makes the CD player skip back through the disc track by track. Once the beginning of the first track is reached, the CD player will not go back any further.

Notes: The Skip Forwards and Backwards buttons can be used to select a desired track to play from before disc play starts. In this case the number of the selected track will be displayed until the Play / Pause Button is pressed.

MANUAL SEARCH

• During playback, pressing the UP or DOWN Search buttons (30) will cause the player to scan through the current track. At the end of a track the player will skip to the next track and continue scanning. At the beginning of a track the player will skip to the previous track and continue scanning.

•When the player reaches the end of the final track, or the beginning of the first track, it will

stop scanning.

INTRO SCAN

•Press the INTRO BUTTON (31) in STOP mode to play the first 10 seconds of each track on the CD. The heading “INTRO” will appear in the display before the track playing. Press this button again, when a desired track is playing, to resume normal playback. “INTRO” will disappear from the display.

Page 5 Page 7
Page 6
Image 6
Curtis RCD904 manual Important Information, To Stop a CD Part WAY Through, Track Skip, To Skip to the Next Track on a Disc
Page 5 Page 7

RCD904 specifications

The Curtis RCD904 is an advanced onboard charger designed to optimize the charging process for electric vehicles and hybrid systems. This compact, lightweight device combines cutting-edge technology with a user-friendly interface, making it a standout choice for manufacturers and consumers alike.

One of the main features of the Curtis RCD904 is its high efficiency. With a conversion efficiency exceeding 90%, this charger minimizes energy loss during the charging process, providing faster charging times and reducing overall energy consumption. This efficiency is essential in today's eco-conscious market, where reducing carbon footprints is a priority.

The RCD904 also boasts a wide input voltage range, typically from 85V to 265V AC, making it versatile enough to accommodate different power systems globally. This adaptability ensures that users can charge their vehicles seamlessly, regardless of their geographical location.

Incorporating advanced communication technologies, the Curtis RCD904 supports the CAN bus protocol, which enables real-time data exchange between the charger and the vehicle's onboard systems. This feature allows for enhanced charge control, allowing users to monitor the charging status and make adjustments as necessary for optimal performance.

Another key characteristic of the RCD904 is its robust design. The charger is engineered to withstand harsh environmental conditions, with an IP67 rating that ensures it is dust tight and can withstand immersion in water, making it suitable for outdoor applications. This durability is complemented by a compact form factor, allowing for easy integration into various vehicle designs without compromising space.

The Curtis RCD904 also includes smart features such as programmable charge profiles and temperature management, which help to prolong battery life by preventing overheating during the charging cycle. This functionality is particularly important in maintaining the health of lithium-ion batteries, which are commonly used in electric vehicles.

In summary, the Curtis RCD904 is a powerful, efficient, and reliable onboard charger that incorporates advanced technologies to enhance the electric vehicle charging experience. With its wide input voltage range, communication capabilities, robust design, and smart features, it stands as a leader in the market, meeting the demands of modern electrification while promoting sustainability and innovation in transportation.
Top Page Image Contents