
QUICK INSTALLATION GUIDE
Remote Management Card
RMCARD203
Intelligent Remote Management Card allows a UPS system and environment sensor to be managed, monitored, and configured
INSTALLATION GUIDE
Step 1. Hardware Installation1. Turn off the UPS before removing the expansion port cover on the UPS.
2. Remove the two retaining screws of the expansion port cover, then remove the cover.
3.Install the CyberPower Remote Management Card into the expansion port.
4.
5. Connect the Ethernet cable to the Ethernet connector of the CyberPower Remote Management Card.
6.To connect with the environment sensor, use the
RJ45 Ethernet cable. Plug one end into the Universal connector and the other end into the sensor.
7. Turn on the UPS.
LINK Indicator
Universal connector |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Ethernet connector |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| RX/TX Indicator |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
| Universal Link |
|
| RX/TX |
|
|
| |||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| RMCARD203 |
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Link LED color | Condition | |
|
| |
| The Remote Management Card is not | |
Off | connected to the Network or the Remote | |
| Management Card power is OFF | |
|
| |
On(Yellow) | The Remote Management Card is connected | |
| to the Network | |
|
| |
TX/RX LED color |
| |
|
| |
Off | The Remote Management Card power is OFF | |
|
| |
On(Green) | The Remote Management Card power is ON | |
|
| |
Flash | - Receiving/transmitting data packet | |
- Reset finished | ||
| ||
|
|
Step 2. Configure the IP address for the CyberPower Remote Management Card.
Method 1: Using the Power Device Network Utility Tool
1.Install the Power Device Network Utility Tool from the included CD. It is located on the CD in the \tools\nework folder. Double click the “Power Device Network Utility” installation file, “Setup.msi” to begin the installation.
2.After installation completes, run the “Power Device Network Utility” (Under “All Programs”, select “CyberPower Power Device Network Utility”.)
3.The main dialog of the Power Device Network Utility Tool program is shown in Figure. 1. The tool will display all Remote Management Cards present on the network. The "Refresh" button is used to search the entire local network again.
Figure 1. The main window of the “Power Device Network Utility” program.
4.Select the Remote Management Card you are setting up. Click on the Tools menu and select “Device Setup” or double click the Remote Management Card you want to configure.
5.You can modify the IP Address, Subnet Mask, and Gateway address for the Device MAC Address listed in the Device Network Settings window, as shown in figure 2. The default IP Address is 192.168.20.177 and the default Subnet Mask is 255.255.255.0.
6.Modify the IP, subnet mask or gateway address. Enter
the new addresses into the | Figure 2. The Device Network setting window. | |
corresponding fields. | ||
|