DR30GS, DR30GFS, DR30GIS, DR30GIFS

Document # PG05-007

Revised 04/04/13 Page 2/5

 

Distinctive 30” Wide

PLANNING

 

All Gas Ranges

GUIDE

All tolerances +1/16” (+1.6 mm), -0 unless otherwise noted.

B

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

13” (33.0 cm)

 

 

Back wall

max.4

 

 

 

 

 

 

immediately

 

 

 

 

 

 

 

behind range6

 

 

 

 

 

 

 

 

Note 1

 

 

 

 

 

 

 

 

 

 

 

 

 

■■ Failure to meet or exceed the maximum and minimum dimensions/clearances stated may result in a fire hazard.

■■ The range should be placed away from drafts that may be caused by doors, windows and heating and air conditioning outlets.

■■ To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage space located above surface units should be avoided. If cabinet storage space is to be provided directly above the range, the risk of personal injury may be reduced by installing a range hood.

Top of

 

 

■■ In all instances, installation of a range hood is highly

 

 

recommended. The hood should project horizontally

finished

 

 

a minimum of five (5) inches beyond the face of

 

 

 

 

counter

 

 

the cabinets. See the range hood specifications for

 

 

 

 

 

 

minimum clearances.

 

Note 5

 

 

 

 

 

 

 

 

 

 

 

 

 

A

 

 

 

 

 

 

14” (35.6 cm)

 

 

 

min.4

 

 

 

 

 

 

 

 

 

Note 2

C

Suggested location of utilities3

■■ If installing a raised vent, install only Dacor model ERV3015.

■■ The range may be installed flush to the rear wall. See diagram and notes for rear wall surface requirements. It is not necessary to install non- combustible materials behind the range below the countertop height.

■■ Any openings in the wall behind the appliance or in the floor underneath it must be sealed.

A*

B

C

30” min.

36” (91.4 cm) recommended

37” (94.0 cm)

(76.2 cm)

30” (76.2 cm) min.

max.

* See the cutout dimensions on following page for self-rimming installations.

Freestanding Installation Cabinet Cutout Dimensions - Models DR30GS, DR30GFS, DR30GIS and DR30GIFS

130” (76.2 cm) min. vertical clearance from top of range grates to bottom of uncovered wood or metal cabinet. 24” (61 cm) min. clearance if bottom of wood or metal cabinets are protected by not less than 1/4“ (0.6 cm) flame retardant millboard covered with no less than No. 28 MSG sheet steel 0.015” (0.04 cm) stainless steel, or 0.024” (0.06 cm) aluminum or 0.020” (0.05cm) copper. 30” (76.2 cm) min. clearance between top of range grates and bottom of unprotected wood or metal cabinet. If installing range hood, check the hood specifications for minimum required clearances.

2Cabinet/countertop depth is at discretion of customer but cabinet face SHALL NOT protrude further than rear of front panel. See Product Dimensions.

3Consult local code and following pages for requirements.

4This specification not applicable for cabinets more than a horizontal distance of 10” (25.4 cm) from edge of range.

510” (25.4 cm) min. to combustible sidewalls above range (both sides).

6Non-combustible surface required for models DR30GIS and DR30GIFS up to vertical distance specified in note 1 or range hood, whichever is lower. Non- combustible surface recommended, but not required, for models DR30GS and DR30GFS.

All specifications subject to change without notice.

www.dacor.com

Phone: (800) 793-0093