Planning the Installation
10” | Min. |
|
|
|
|
| 7/16” | ||
|
|
|
| ||||||
(254mm) |
|
|
|
|
| ||||
Rear Wall |
|
|
|
|
| (11mm) | |||
Both | Sides |
|
|
|
|
| |||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
29 1/4” (743mm) 
Countertop
Opening23 9/16” (598mm)
30 1/16” (764mm)
Cabinet
Opening
Combustible Side
Wall Above Range
1”
(25mm)
|
|
|
|
|
|
| 10” Min. |
|
|
| 1/4” Min. | ||||||||||
|
|
|
|
|
|
|
|
| |||||||||||||
|
|
|
| Rear Wall | (254mm) |
|
|
| |||||||||||||
|
|
|
| Both Sides |
|
|
|
|
| (6mm) | |||||||||||
|
|
|
|
|
|
|
|
| |||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 27 7/8” (708mm) |
|
|
|
|
|
|
|
|
|
|
| 2 13/16” (71mm) | |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
| ERV Opening |
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
| ||||||||||||
|
|
|
|
|
| 29 1/4” (743mm) |
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| |||||||||||
|
|
|
|
|
| Countertop |
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
| 24 1/16” |
|
| |||||||||||||
|
|
|
|
|
|
| Opening |
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| (611mm) |
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
| 30 1/16” (764mm) |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||
|
|
|
|
|
|
| Cabinet |
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| Opening |
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
| Combustible Side |
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
| ||||||||||||
|
|
|
|
|
| Wall Above Range |
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
| |||||||||||||
Minimum Cabinet depth: 27 1/8” (688mm) | 1” | ||||||||||||||||||||
Minumum Countertop depth: 28 1/8” (714mm) | (25mm) | ||||||||||||||||||||
Cabinet Cutout Dimensions | Cabinet Cutout Dimensions |
Self Rimming Installation | Self Rimming Installation |
| with ERV Raised Vent |
Notes on | Notes on |
•The above specifications assume a standard 24 inch cabinet depth and 25 inch countertop depth.
•When sliding the range into position, the range stops when the rear of the control panel hits the 1” notch in the countertop, leaving a 7/16” gap between the rear trim and the wall behind.
•The top and rear trim for the ERV trim kit are 1/2” deeper than the trim for installations without an ERV to allow the range to clear the ERV.
•When sliding the range into position, the range stops when the rear of the control panel hits the 1” notches in the front of the countertop.
NOTE: If installing in a deeper countertop or installing a custom backguard, you may install the available 3” side panel kit to allow for custom countertop notches of 1 to 4 inches.
Installation Instructions
Preparing for Installation
WARNING
•If the gas or electric service provided does not meet the product specifications, do not proceed with the installation. Call the dealer, the gas supplier or a licensed electrician.
•Before installing the range, you must locate and secure the
•Be sure that the unit is not connected to gas or power before proceeding with the following sections.
IMPORTANT: Within the Commonwealth of Massachusetts, this appliance must be installed by a licensed plumber or gas fitter.
NOTE: When installing a backguard, always install it before sliding the range into place. See page 9.
Unpack the Range
Parts List
• | 2 | Grates | • | 4 Knobs |
• | 1 | Small Stack Burner Cap | • |
•1 Small Stack Burner Ring • Meat Probe
•2 Large Stack Burner Caps • Griddle
•2 Large Stack Burner Rings • Wok Ring
• | 1 | Crown Burner Cap | • | Stainless Steel Cleaner |
• | 1 | Crown Burner Ring | • | Lens Pry Stick |
• | 1 | Crown Burner Head | • | Literature Kit |
•1 GlideRack™ Oven Rack • Ignitor Cleaning Brush
• 2 Standard Size Racks | • Broiler Pan/Grill |
See the use and care manual for a list of optional parts and accessories.
Unpack the range and verify that all required parts have been provided. If any item is missing or damaged, please contact your dealer immediately. Do not install a damaged or incomplete appliance. The customer must report cosmetic issues within 30 days of installation.
NOTE: The range also includes a thread ring removal tool
(Part # 101539) for the crown burner. It is tie wrapped in place behind the right side of the kick panel when the range is shipped from the factory. Leave it in place unless the spill tray needs to be removed for service. Return it after use so that it is available if needed in the future.
Thread Ring Removal Tool Location