Operating Instructions
Circuit d’alimentation électrique - Spécifications
Indicator Light Function:
Power Light (Green):
When the unit is first connected to an electrical outlet, the (green) power light starts to flash and continues to flash until the “on/off” button is pressed. When the “on/off” button is activated, the flashing (power) light turns to a steady state “on” condition. The dehumidifier will automatically default to the factory default setting. (See Factory Default Setting for details)
IMPORTANT NOTE: Depending on the humidity conditions of the surrounding environment, the dehumidifier may not start automatically when the “on/off” button is pressed.(see dehumidifier operating instructions for details)
In the event of a power failure, the unit will not
Water Full Indicator Light (Red):
When the water tank is full and /or incorrectly positioned inside the cabinet, the (water full) red light turns on and remains on until such time the tank is emptied and/or correctly
Factory Default Setting:
Each time the unit is
Humidity Setting: 60%
Fan Speed: Low
NOTE: In the event of a power failure, all previous settings are automatically erased/cancelled. If your program setting was different than the above (default setting) it will be necessary to
Water Tank Operation:
Proper installation of the water tank is crucial in maintaining reliable dehumidifier operation.
The water tank holds accumulated condensed water and by means of a safety switch controls both the water level and operation of the dehumidification process.
i.e. When the water tank is full and/or accidentally displaced inside the cabinet, the float switch actuator (inside the tank) breaks contact with the safety switch. This condition results in the immediate shut down of the compressor and fan motor system, preventing moisture from being condensed.
IMPORTANT: Never tamper with or attempt to defeat the water level (safety) float switch system.
1.Tout câblage doit être réalisé par un électricien qualifié, en conformité avec les prescriptions des codes national et local régissant les installations électriques. Pour toute question au sujet des instructions qui suivent, contacter un électricien qualifié.
2.AVANT l’installation et AVANT l’utilisation de cet appareil, contrôler les caractéristiques de la source d’électricité, et résoudre tout problème affectant le câblage.
3.Pour la sécurité et la protection des utilisateurs, cet appareil est relié à la terre lorsqu’il est branché sur une prise de courant de même configuration que la fiche de branchement. En cas de doute quant à la qualité de la liaison à la terre de la prise de courant, consulter un électricien qualifié. NE JAMAIS
UTILISER UN CÂBLE DE RALLONGE NI UN ADAPTATEUR SI LA CONFIGURATION DE LA FICHE DE BRANCHEMENT NE CORRESPOND PAS À CELLE DE LA PRISE DE COURANT.
4.La plaque signalétique de l’appareil est située sur la paroi arrière du compartiment du réceptacle à eau; on y trouve les caractéristiques électriques et techniques spécifiques de cet appareil.
5.Pour éviter les risques de dommage corporel, on doit toujours débrancher l’appareil de la source d’électricité avant d’entreprendre des travaux de nettoyage ou d’entretien.
Spécifications de l’appareil: | DDR2506 |
| |
| Capacité de déshumidification (Pintes/Litres) | 25/11.8 |
|
|
|
|
|
| Alimentation électrique | 115 Volts / 60 Hz |
|
|
|
|
|
| Consommation d’énergie (watts) | 490 |
|
|
|
|
|
| Demande de courant nominale |
|
|
|
|
|
|
| • Déshumidification | 4.5 |
|
|
|
|
|
| Débit de circulation d’air maxi (pieds cubes par minute) | 118 |
|
| Type de réfrigérant | R22 |
|
| Capacité du réceptacle à eau (litres) | 5 / 10.55 |
|
|
|
|
|
| Niveau de bruit en fonctionnement (dB A) | 50 |
|
| Dimensions (largeur/hauteur/profondeur) |
| |
|
|
|
|
| Poids net (kg/lb) | 14.5/32 |
|
|
|
|
|
NOTE: Les spécifications sont sujettes à modification sans préavis (pour l'amélioration des produits).
8 | 16 |