Dell H950N, H967N, J728N, K803N UPS Initial Startup

29

Installation |

UPS Initial Startup

To start up the UPS:

1Verify that the internal batteries are connected.

2If an optional EBM is installed, verify that the EBM is connected to the UPS.

3Verify that the power input to the UPS has adequate upstream overcurrent protection:

Table 1. Minimum Upstream Circuit Breaker Rating

UPS Output Power 120V 208V 230V

2700W 30A 20A 16A

The power cord current ratings are listed in Table 2.

Table 2. Power Cord Ratings

Dell UPS Model and Voltage Power Cord Rating Country Supplied Cord Set

2700W 208V L6-20P to C19 15A North America Yes

C19 to C20 Jumper 16A North America Optional

2700W 230V

CEE 7/7 Schuko to C19 16A Europe (Schuko) Yes

BS 1363 to C19 13A United Kingdom (New) Yes

GB2009.1 to C19 16A China Yes

C19 to C20 Jumper 16A Europe/Australia Yes

C19 to C20 Jumper 16A China Yes

BS 546 to C19 15A United Kingdom(Old) Optional

TI16S3 to C19 16A Thailand Optional

AS 3112 to C19 15A Australia Optional

IRAM2073 to C19 16A Argentina Optional

CEI 23-50 to C19 16A Italy Optional

KSC8305 to C19 15A South Korea Optional

IS 1293 to C19 16A India Optional

NBR 14136 to C19 16A Brazil Optional

C19 to C20 Jumper 16A North America Optional

L6-20P to C19 15A North America Optional

Contents

Main Notes and Warnings S Table of Contents 1 Introduction 2 Safety Warnings 3 Installation 4 Operation 5 Additional UPS Features Page Introduction Page Finding Information NOTE: NOTE: Safety Warnings IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS S Page Page Installation Inspecting the Equipment Unpacking the Cabinet Page Installation Identifying the UPS Rear Panels Figure 5. 2700W, 208V Rear Panel This section shows the rear panels of the Dell Online Rack models. Figure 4. 2700W, 120V Rear Panel Figure 6. 2700W, 230V Rear Panel Identifying the UPS Front Panel Figure 7. The Dell Online Rack UPS Front Panel Rackmount Setup Page Page Page Page Page Page Installing the EBM Page Installing the UPS Installing Remote Emergency Power-off Page UPS Initial Startup To start up the UPS: The power cord current ratings are listed in Table 2. Page Operation UPS Startup and Shutdown Starting the UPS Starting the UPS on Battery UPS Shutdown Control Panel Functions S S S Changing the Language Display Functions Startup Screen Screen Locked UPS Status Page Page Event Log Measurements Control Screens Table 6 describes the available control screens. Identification S S S S S Settings Page Page Page Page Transferring the UPS Between Modes S S Transferring from Normal to Bypass Mode Transferring from Bypass to Normal Mode Setting Power Strategy Retrieving the Event Log To retrieve the Event Log through the display: 1Press the button for one second to go to the main menu selection and scroll down to the Event Log menu using the button. Behavior on Overload Configuring Load Segments Controlling Load Segments Through the Display Configuring Automatic Start Delay S S S S Configuring Automatic on Battery Shutdown Configuring Battery Settings Configuring the UPS for an EBM Running Automatic Battery Tests S S S S Configuring Automatic Restart Additional UPS Features S S S RS-232 and USB Communication Ports Page Dell Network Management Card (Optional) Dell UPS Management Software UPS Maintenance S S S S S UPS and Battery Care Transporting the UPS Page Page Storing the UPS and Batteries When to Replace Batteries Testing Batteries S S S Updating the UPS Firmware Specifications This chapter provides the following specifications: S S S S S S NOTE: Page Troubleshooting Accessing Alarms and Conditions S S UPS Status Menu S Typical Alarms and Conditions Page Page Page Silencing the Alarm