Manuals / Dell / Computer Equipment / Server

Dell T7610 owner manual Installing the Thermal Sensor, Removing the Processor

Models: T7610

1 81

Download 81 pages 45.18 Kb

Page 41

Image 41

5.Open the latch securing the thermal sensor and remove it from the computer.

Installing the Thermal Sensor

1.Install the thermal-sensor cable on the system board.

2.Route the thermal-sensor cable around the computer chassis.

3.Fasten the latch that secures the thermal-sensor cable.

4.Install:

a.air tunnel (if available)

b.right cover

c.left cover

5.Follow the procedures in After Working Inside Your Computer.

Removing the Processor

1.Follow the procedures in Before Working Inside Your Computer.

2.Remove:

a.cover

b.air tunnel (if available)

c.heatsink

Page 41

Image 41

Dell T7610 owner manual Installing the Thermal Sensor, Removing the Processor

Contents

Regulatory Model D02X Regulatory Type D02X002 Dell Precision Workstation T7610 Owners ManualNotes, Cautions, and Warnings 1 Working on Your Computer Contents2 Removing and Installing Components 5 Diagnostics 4 System Setup6 Troubleshooting Your Computer 3 Additional InformationContacting Dell Technical SpecificationsPage Before Working Inside Your Computer Working on Your ComputerAfter Working Inside Your Computer Turning Off Your ComputerPage Page System Overview Removing and Installing ComponentsRecommended Tools Installing the Power Supply Unit PSU Removing the Power Supply Unit PSU1. Follow the procedures in Before Working Inside Your Computer 2. Follow the procedures in After Working Inside Your Computer3. Follow the procedures in After Working Inside Your Computer Installing the Front CoverRemoving the Front Cover 1. Follow the procedures in Before Working Inside Your Computer1. Follow the procedures in Before Working Inside Your Computer Removing the Hard Drive2. Remove the front cover 3. Pull the clasp of the hard-drive bracket in an outward direction7. Flex the hard-drive bracket on both sides to loosen the hard drive 5. Follow the procedures in After Working Inside Your Computer Installing the Hard DriveRemoving the Left Cover Installing the Left Cover1. Follow the procedures in Before Working Inside Your Computer 3. Follow the procedures in After Working Inside Your ComputerInstalling the Intrusion Switch Removing the Intrusion Switch4. Follow the procedures in After Working Inside Your Computer Removing the PCI CardRemoving the Slimline Optical Drive Installing the PCI Card4. Follow the procedures in After Working Inside Your Computer 1. Follow the procedures in Before Working Inside Your Computer3. Disconnect the cable from the back of the optical drive 4. Disconnect the power cable from the back of the optical drivePage Removing the Air Tunnel Installing the Slimline Optical Drive4. Follow the procedures in After Working Inside Your Computer 1. Follow the procedures in Before Working Inside Your Computer4. Follow the procedures in After Working Inside Your Computer Installing the Air TunnelRemoving the Coin-Cell Battery Installing the MemoryRemoving the Memory 1. Follow the procedures in Before Working Inside Your ComputerRemoving the Heatsink Installing the Coin-Cell Battery4. Follow the procedures in After Working Inside Your Computer 1. Follow the procedures in Before Working Inside Your ComputerRemoving the Heat-Sink Fan Installing the Heatsink5. Follow the procedures in After Working Inside Your Computer 1. Follow the procedures in Before Working Inside Your ComputerRemoving the System Fan Installing the Heatsink Fan4. Follow the procedures in After Working Inside Your Computer 1. Follow the procedures in Before Working Inside Your Computer6. Remove the graphics-card cable from the latch Page 10. Disconnect the system-fan cable connectors from the system board 10. Follow the procedures in After Working Inside Your Computer Installing the System FanRemoving the I/O Panel and the USB 3.0 Ports 1. Follow the procedures in Before Working Inside Your Computer3. Disconnect all the cables from the I/O panel Installing the I/O Panel and the USB 3.0 Ports 1. Follow the procedures in Before Working On Your Computer Removing the Power Switch7. Follow the procedures in After Working Inside Your Computer Removing the Speaker Installing the Power Switch5. Follow the procedures in After Working Inside Your Computer 1. Follow the procedures in Before Working Inside Your Computer4. Follow the procedures in After Working Inside Your Computer Installing the Speaker2. Remove the screws that secure the right cover to the chassis Removing the Right Cover1. Follow the procedures in Before Working Inside Your Computer Removing the 5.25-inch Optical Drive Installing the Right Cover3. Follow the procedures in After Working Inside Your Computer 1. Follow the procedures in Before Working Inside Your ComputerRemoving the Thermal Sensor Installing the 5.25-inch Optical Drive5. Follow the procedures in After Working Inside Your Computer 1. Follow the procedures in Before Working Inside Your Computerb. Unroute the thermal-sensor cable through the chassis clips 3. Perform the following stepsa. Disconnect the thermal-sensor cable from the system board Removing the Processor Installing the Thermal Sensor5. Follow the procedures in After Working Inside Your Computer 1. Follow the procedures in Before Working Inside Your ComputerInstalling the Processor Removing the Hard-Drive Fan 6. Follow the procedures in After Working Inside Your Computer1. Follow the procedures in Before Working Inside Your Computer 2. Remove a. left cover b. right cover c. PCI cardRemoving the Power Supply Unit PSU Card Installing the Hard-Drive Fan4. Follow the procedures in After Working Inside Your Computer 1. Follow the procedures in Before Working Inside Your Computer1. Install the screws that secure the PSU card to the chassis Installing the Power Supply Unit PSU Card2. Connect all the cables to the PSU card 3. Install the right cover 4. Follow the procedures in After Working Inside Your Computer1. Follow the procedures in Before Working Inside Your Computer Removing the System Boardh. chassis intrusion switch i. coin-cell battery j. PCI card 3. Disconnect all the connectors from the system board3. Connect the connectors to the system board Installing the System Board4. Remove the screws that secure the system board to the chassis 2. Tighten the screws that secure the system board to the chassis5. Follow the procedures in After Working Inside Your Computer System Board Componentsintrusion-switch connector Page Front Panel Chassis Lock Additional InformationMemory Module Guidelines Power Supply Unit PSU Lock Navigation Keys System SetupBoot Sequence System Setup Options Table 3. System Configuration NOTE If the hard drives are connected to a RAID controller card Table 5. Security Table 4. VideoTable 7. Performance Table 6. Secure BootDefault Setting Enable Dell Reliable Memory Default Setting Enable Hardware PrefetchTable 10. Virtualization Support Table 9. POST BehaviorUpdating the BIOS Assigning a System Password and Setup Password System and Setup PasswordDisabling a System Password Deleting or Changing an Existing System and/or Setup Password11. Follow the procedures in After Working Inside Your Computer 1. Follow the procedures in Before Working Inside Your ComputerPage Enhanced Pre-Boot System Assessment ePSA Diagnostics DiagnosticsPage Diagnostic LEDs Troubleshooting Your ComputerA possible graphics card failure has occurred Errors That Halt Your Computer Completely Error MessagesErrors That Soft Halt Your Computer Errors That Do Not Halt Your ComputerTable 15. Errors that do not halt your computer Table 16. - Errors that soft halt your computerDell Reliable Memory Technology RMT has discovered and isolated errors in system memory. You may continue to work. Memory module replacement is recommended. Please refer to the RMT Event log screen in BIOS setup for specific DIMM information Page Table 17. Processor Technical SpecificationsTable 18. System Information Table 19. MemoryTable 21. Audio Table 20. VideoTable 22. Network Table 23. Expansion Interfacessupports one 5.25-inches SATA device or supports one Table 25. External ConnectorsTable 24. Drives two 164-pin connectors four when optional second processor is Table 26. Internal Connectorsblinking amber light - indicates a problem has occurred with the solid amber light - the computer does not start, indicating a problemFront USB Internal USB Front panel control Table 27. Controls and LightsTable 28. Power amber/blinking light - see the service manual for specific diagnostic4015.3 BTU/Hr at 100 VAC 4365.5 BTU/Hr at 107 VAC105 G +/- 5% with pulse duration of 2 msec +/- 10% equivalent to Table 30. Environmental40 G +/- 5% with pulse duration of 2 msec +/- 10% equivalent to Page 1. Visit dell.com/support Contacting Dell