DISPLAYED MESSAGES
DISPLAYED MESSAGE | POSSIBLE CAUSE | REMEDY |
|
|
|
| |
FILL TANK | Insufficient water in the tank. | Fill the tank with water and/or insert it correctly, pushing it | |
|
| as far as it will go until it clicks into place. | |
|
|
| |
EMPTY GROUNDS CONTAINER | The grounds container (A22) is full. | Empty the grounds container and drip tray, clean and replace | |
|
| (fig. 26). |
|
|
| Important: when removing the drip tray, the grounds contai- | |
|
| ner must be emptied, even if it is not completely full. | |
|
| If this is not done, when you make the next coffees, the | |
|
| grounds container may fill up more than expected and clog | |
|
| the machine. |
|
|
|
| |
GROUND TOO FINE ADJUST | The grinding is too fine and the coffee is delivered too slowly | Repeat coffee delivery and turn the grinding adjustment | |
MILL | or not at all. | dial (fig. 12) one click clockwise towards “7” while the coffee | |
| mill is in operation. |
| |
alternating with |
|
| |
| If after making at least 2 coffees delivery is still too slow, | ||
Insert water spout and press |
| repeat the correction procedure, turning the grinding | |
OK |
| adjustment dial another click (see the section “adjusting the | |
|
| coffee mill” on page 12). |
|
INSERT GROUNDS CONTAINER | After cleaning, the grounds container has not been repla- | Remove the drip tray and insert the grounds container. | |
| ced |
|
|
ADD | The | Place | |
| placing any | the |
|
DESCALE! | The machine must be descaled. | The descaling procedure described in the "descaling" section | |
|
| (page 17) needs to be performed as soon as possible. | |
|
|
|
|
LESS COFFEE | Too much coffee has been used. | Select a milder taste by pressing the | button (fig. |
|
| 9) or reduce the quantity of | |
|
|
| |
|
|
|
|
FILL BEANS CONTAINER | The coffee beans have run out. | Fll the beans container (fig. 13). |
|
|
|
| |
| The | Clear the funnel with the help of a brush as described in the | |
|
| section “Cleaning the | |
|
|
| |
INSERT INFUSER ASSEMBLY | The infuser has not been replaced after cleaning. | Insert the infuser as described in the section “cleaning the | |
|
| infuser”. |
|
|
|
| |
INSERT TANK | The tank is not correctly in place. | Insert the tank correctly and press as far as it will go. | |
|
|
| |
GENERAL ALARM | The inside of the appliance is very dirty. | Clean the inside of the appliance thoroughly, as described in | |
|
| the section “cleaning and maintenance”. |
|
|
| If the message is still displayed after cleaning, contact | |
|
| De’Longhi Customer Experience. |
|
|
|
|
|
EMPTY CIRCUIT FILL CIRCUIT | The water circuit is empty | Connect the water spout (D3) (fig.6), fill | the water tank and |
alternating with |
| press ok to deliver water from it, until it flows out normally. | |
Hot water press OK |
|
|
|
REPLACE FILTER | The water filter is exhausted. | Replace the filter or remove it as described in the section | |
|
| “Water filter”. |
|
Press CLEAN | Milk has been delivered recently and the tubes inside the | Press the CLEAN button (fig. 23) and keep it pressed until the | |
| milk container must be cleaned. | progress bar which appears on the display together with the | |
|
| message “Cleaning underway “ is complete. | |
|
|
| |
INSERT WATER SPOUT | The hot water spout is not inserted or is inserted incorrect- | Insert water spout (D3) as far as it will go. | |
| ly. |
|
|
INSERT MILK CONTAINER | The milk container is not inserted correctly. | Insert the milk container as far as it will go (fig. 21). | |
|
|
|
|
20