BASIC ELEMENTS OF ENGINE

Refer to the engine manual for location and operation of engine controls. Choke Control: Opens and closes carburetor choke valve

Throttle Control Lever: Controls engine speed.

Fuel Valve Lever: Opens/closes connection between fuel tank and carburetor.

Starter Grip: Pulling starter grip operates recoil starter to crank engine.

PRESSURE WASHER TERMINOLOGY

PSI: Pounds per Square Inch. The unit of measure for water pressure. Also used for air pressure, hydraulic pressure, etc.

GPM: Gallons Per Minute. The unit of measure for the flow rate of water.

CU: Cleaning Units. GPM multiplied by PSI.

Bypass Mode: In Bypass Mode, the pump is recirculating water because the trigger of the spray gun is not pulled. If unit is left in bypass mode for more than two (2) minutes, the water temperature will rise to a dangerous level and could damage internal components of the pump. Any damage to pump due to these causes will not be covered under warranty.

DO NOT allow your unit to operate in bypass mode for more than two minutes at any time. Overheating of pump can

cause damage to pump.

Thermal Relief Valve: In an effort to prevent extreme damage, pumps are equipped with a thermal relief valve. This valve will open when the temperature inside the pump rises too high. This valve will then release a gush of water in an effort to lower the temperature inside the pump. Immediately after this occurs, the valve will close. The thermal relief valve is part of the pump and is not visible to the user.

Chemical Injection System: Mixes cleaning solution with the water to improve cleaning effectiveness.

Water Supply: All pressure washers must have a source of water. The minimum requirements for a water supply are 20 PSI and 5 gallons per minute.

PRESSURE WASHER OPERATING FEATURES

PRESSURE ADJUSTMENTS

The pressure setting is preset at the factory to achieve optimum pressure and cleaning. If you need to lower the pressure, it can be accomplished by these methods.

1.Back away from the surface to be cleaned. The further away you are, the less the pressure will be on the surface to be cleaned.

2.Rotate the nozzle at the end of the multi-adjustable spray wand to widen the fan spray. The wider fan spray will minimize the pressure on the surface to be cleaned.

DO NOT attempt to increase pump pressure. A higher pressure setting than the factory set pressure may damage pump.

D27918

12- ENG

Page 11 Page 13
Page 12
Image 12
Delta DT2400CS instruction manual Basic Elements of Engine, Pressure Washer Terminology, Pressure Washer Operating Features
Page 11 Page 13

DT2400CS specifications

The Delta DT2400CS is a high-performance tool that caters to the needs of both professionals and enthusiasts in woodworking and construction. This compact yet powerful saw is engineered for precision, durability, and ease of use, making it an essential addition to any workshop.

One of the standout features of the Delta DT2400CS is its robust 15-amp motor, which provides substantial cutting power and enables the saw to tackle a variety of materials effortlessly. The motor supports a high no-load speed, ensuring smooth and efficient operation. This allows users to cut through hardwoods, softwoods, and composite materials without encountering bogging down or stalling.

The DT2400CS is equipped with a 24-inch capacity, making it ideal for larger workpieces without sacrificing the portability that many users desire. Its adjustable table height and width provide added flexibility and support for various cutting tasks, allowing operators to achieve superior accuracy in their cuts. The saw features a precision-ground cast iron table for stability and reduced vibration, ensuring cleaner cuts and improving the overall experience.

Safety is a top priority with the Delta DT2400CS, which includes a range of protective features. The blade guard is easily adjustable and removable, ensuring that operators can maintain proper safety practices while having clear visibility of the cutting line. The integrated riving knife helps prevent kickback, and the on/off switch is conveniently located for quick access during operation.

The Delta DT2400CS also incorporates advanced technology for enhanced performance. The built-in dust collection port facilitates a cleaner workspace by connecting to standard shop vacuums, which is essential for maintaining visibility and safety. Additionally, the saw has a sturdy fence system that locks securely in place, allowing for straight, consistent cuts.

Overall, the Delta DT2400CS is characterized by its blend of power, precision, and safety features, making it an optimal choice for carpenters, cabinet makers, and DIY enthusiasts alike. With its professional-grade specifications and user-friendly design, this table saw is designed to handle a wide range of cutting tasks, elevating users' woodworking projects to the next level. Whether working on intricate designs or large construction projects, the Delta DT2400CS proves to be a reliable ally, ensuring both quality results and user satisfaction.
Top Page Image Contents