Warning
￿ This instruction sheet only provides introductory information on electrical specification, installation and wiring. ￿ Switch off the power before wiring. DO NOT touch any terminal when the power is switched on.
￿ IFD9506 is an OPEN-TYPE device and therefore should be installed in an enclosure free of airborne dust, humidity, electric shock and vibration. The enclosure should prevent non-maintenance staff from operating the device (e.g. key or specific tools are required to open the enclosure) in case danger and damage on the device may occur.
￿ Introduction
￿ Features
1. Auto-detects 10/100 Mbps transmission speed; MDI/MDI-Xauto-detection.
2. The monitor table temporarily stores the monitored data for the user to fast save or acquire the data.
3. Supports Modbus TCP protocol (supports Master and Slave mode)
4. Able to send out emails after being triggered.
5. The station address, RS-485 communication format and baud rate can be set up externally.
6. The communication parameters can be set up through Web.
￿ Product Profile & Outline
1 Communication ports: RS-485,
Ethernet, RS-232

￿RS-485 Connector

Interface

RJ-11

Transmission method

RS-485

Transmission speed

110, 150, 300, 600, 1,200, 2,400, 4,800, 9,600, 19,200, 38,400, 57,600, 115,200

Communication format

Stop bit: 1,2 Parity bit: None, Odd, Even Data bit: 7,8 ASCII/RTU

Communication

Modbus, User Define

protocol

 

 

￿RS-232 Connector

Interface

Mini Dim

Transmission method

RS-232

Transmission speed

110, 150, 300, 600, 1,200, 2,400, 4,800, 9,600, 19,200, 38,400, 57,600, 115,200

Communication format

Stop bit: 1,2 Parity bit: None, Odd, Even

Data bit: 7,8

ASCII/RTU

Communication

Modbus, Delta Configuration, User Define

 

 

protocol

 

 

 

 

 

Transmission cable

DVPACAB215 / DVPACAB230 / DVPACAB2A30

 

￿RJ-11 PIN Definition

PIN

Signal

Definition

 

PIN

Signal

Definition

1

--

N/C

 

4

D-

Negative pole for data

2

--

N/C

 

5

GND

Ground

3

D+

Positive pole for data

 

6

--

N/C

￿RJ-45 PIN Definition

PIN

Signal

Definition

 

PIN

Signal

Definition

1

Tx+

Positive pole for data

 

5

--

N/C

transmission

 

 

 

 

 

 

 

2

Tx-

Negative pole for data

 

6

Rx-

Negative pole for data

transmission

 

receiving

 

 

 

 

 

3

Rx+

Positive pole for data

 

7

--

N/C

receiving

 

 

 

 

 

 

 

4

--

N/C

 

8

--

N/C

 

注意事項

 

 

 

￿

 

 

 

 

 

￿

 

 

 

 

 

￿

(OPEN TYPE)

 

 

 

 

衝擊意外之外殼配線箱內。另必機須殼具，備因保此護使措用施者（使如用：本特機殊時之，工必具須或將鑰之匙安才裝可於打具開防），塵防、止防非潮維及護免人於員電操擊作∕

￿

 

 

 

 

￿

 

 

 

 

 

1.

10/100 Mbps

MDI/MDI-X

 

2.

Monitor table

 

 

 

 

3.

Modbus TCP

(

Master

Slave

)

4.

此安裝手冊只提供

氣規格、一般規格、安裝及配線等。

 

 

配線時請務必關閉電源，請勿在上電時觸摸任何端子。

 

型 放 開 為 機 本

 

 

 

 

￿Terminal Block

 

Interface

Feed-through terminal 10PIN

 

Transmission method

RS-485

 

Transmission distance

1,200m

 

Transmission speed

110, 150, 300, 600, 1,200, 2,400, 4,800, 9,600, 19,200, 38,400, 57,600, 115,200

 

Communication format

Stop bit: 1,2 Parity bit: None, Odd, Even Data bit: 7,8 ASCII/RTU

 

Communication

Modbus, User Define

 

protocol

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

￿RS-232 PIN Definition

PIN

Signal

Definition

 

PIN

Signal

1

--

N/C

 

5

Tx

2

--

N/C

 

6

--

3

--

N/C

 

7

--

4

Rx

Reception data

 

8

GND

￿Feed-through Terminal PIN Definition

Definition

Transmission data

N/C

N/C

Ground

5.

 

RS-485

 

 

 

 

 

6. Web

 

 

 

 

 

 

￿

 

 

 

 

 

 

 

 

產品外觀

 

 

 

1

通訊口

RS-485, Ethernet,

 

 

 

 

 

 

或意外衝擊本體，造成危險及損壞。

 

 

 

RS-232

 

 

 

2

 

 

 

 

 

3

 

 

 

 

 

4

 

 

 

 

 

 

 

 

 

產品簡介

 

 

 

 

 

 

 

功能特色

傳輸速率，

 

自動偵測。

 

 

 

 

自動偵測

 

 

 

 

 

提供

可暫存監控的資料，讓使用者快速存取。

 

 

 

 

支援

協定 支援

和

模式 。

 

 

 

￿Electrical Specifications

Power voltage

24V DC (-15% ~ 20%) supplied by feed-through terminal

Power consumption

3W

Insulation voltage

500V

Weight

140g

￿Environment

 

ESD (IEC 61131-2, IEC 61000-4-2): 8KV Air Discharge

 

EFT (IEC 61131-2, IEC 61000-4-4): Power Line:±2KV, Digital Input: ±2KV,

 

Communication I/O: ±2KV

 

RS (IEC 61131-2, IEC 61000-4-3): 80MHz ~ 1GHz, 10V/m. 1.4GHz ~ 2.0GHz,

Noise immunity

10V/m

PIN

Signal

 

 

1SG

2D-

3D+

4X2

5X1

6X0

7S/S

824V

90V

10

 

--

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Definition

Ground of signal

Data-

Data+

Digital input 2

Digital input 1 Digital input 0 Ground of digital input +24V

0V

Earth ground

 

 

 

5

 

 

 

 

 

 

 

 

6

RS-485

 

Reset

 

 

 

 

Ethernet

 

按鍵、

 

 

 

7

 

 

 

 

 

 

 

 

8

端子台

RS-485

 

 

 

 

 

 

連接器、數位輸入

 

 

 

 

 

 

 

 

 

 

 

9

DIN

 

 

 

 

￿

 

 

 

 

 

 

 

 

經觸發後發送電子郵件。

通訊格式、鮑率。

 

 

 

 

 

 

 

外部設定站號、

 

電源指

 

燈

 

￿ Ethernet

 

 

 

 

可由

設定通訊參數。

 

 

 

 

 

 

 

 

站號設定開關

 

 

 

 

 

 

格式、通訊速率設定開關

 

 

 

 

數位顯示器

 

 

Conducted Susceptibility Test (EN61000-4-6, IEC61131-2 9.10): 150KHz ~

 

80MHz, 3V/m

 

Surge Test (Biwave IEC61132-2, IEC61000-4-5):

 

Power line 0.5KV DM, Ethernet 0.5KV CM, RS-485 0.5KV CM

Operation/storage

Operation: 0ºC ~ 55ºC (temperature), 50 ~ 95% (humidity), pollution degree 2

Storage: -25ºC ~ 70ºC (temperature), 5 ~ 95% (humidity)

 

Vibration/shock

International standards: IEC61131-2, IEC68-2-6 (TEST Fc)/IEC61131-2 & IEC

immunity

68-2-27(TEST Ea)

Certificates

 

￿LED Indicators & Trouble-Shooting

There are 3 LED indicators and a digital display on IFD9506. POWER indicator displays the status of the working power. RS-485 and LINK/ACT indicators display the connection status of the communication. The digital display shows the address of and errors in IFD9506 and the error messages from the slave.

￿POWER LED

LED status

Indication

How to correct

OFF

Working power is abnormal

Check if the working power of IFD9506 is normal.

Green light ON

Working power is normal

--

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

連接器RJ-45 with Auto MDI/MDIX

 

 

 

Ethernet Type II

 

 

 

 

Category 5e, 100

(Max)

 

 

 

10/100 Mbps Auto-Detection

 

 

 

ICMP, IP, TCP, UDP, DHCP, SMTP, MODBUS OVER TCP/IP, Delta Configuration

 

 

 

指示燈、

 

 

 

模組名稱

指示燈

功能規格

 

 

點、電源輸入、大地

 

 

軌連接器

￿Installation

￿Dimension

￿RS-485 LED

LED status

Indication

How to correct

 

No communication or RS-485

1. If the LED is off during the communication, check if the RS-485 in

OFF

IFD9506 is normally connected.

connection is abnormal.

 

2. Check at least 1 node on the network is communicating normally.

 

 

Constantly ON

Abnormal RS-485 connection

Switch D+ and D-

Green light

RS-485 connection is normal.

--

flashes

 

 

￿LINK/ACT LED

LED status

Indication

How to correct

 

 

1. Check the power of IFD9506 and make sure the network

OFF

No power, or no network

connection is normal.

connection

2. Re-power IFD9506. If the error still exists, send your IFD9506

 

 

 

back to the factory for repair.

Green light ON

The connection is normal, but no

--

 

data transmission.

 

Green light

The data transmission is normal. --

flashes

 

 

￿ RS-485

 

 

 

 

 

 

 

連接器RJ-11

 

 

 

 

 

 

RS-485

 

 

 

 

 

 

110, 150, 300, 600, 1,200, 2,400, 4,800, 9,600, 19,200, 38,400, 57,600, 115,200

 

 

 

Stop bit: 1,2

Parity bit: None, Odd, Even

Data bit: 7,8

ASCII/RTU

 

 

 

Modbus, User Define

 

 

￿ RS-232

 

 

 

 

 

接頭

方式

連接器Mini Dim

 

 

 

 

RS-232

 

 

 

 

110, 150, 300, 600, 1,200, 2,400, 4,800, 9,600, 19,200, 38,400, 57,600, 115,200

 

 

Stop bit: 1,2

Parity bit: None, Odd, Even

Data bit: 7,8

ASCII/RTU

 

 

電纜

 

 

 

公尺

 

 

 

傳輸速率

Modbus, Delta Configuration, User Define

 

 

 

DVPACAB215 / DVPACAB230 / DVPACAB2A30

 

 

網路協定

 

 

 

 

￿

接頭

方

 

 

 

 

 

 

 

 

 

 

傳輸速率

 

 

 

 

 

 

格

 

 

 

 

 

 

協定

 

 

 

 

2

Power indicator

3

Address switch

4

Data format/baud rate switch

5

Digit display

6

RS-485 indicator, Reset button,

 

Ethernet indicator

7

Module name

8

RS-485 connector, digital input points,

 

power input point, earth point

9

DIN rail connector

￿ Specifications

￿ Ethernet Interface

Interface

RJ-45 with Auto MDI/MDIX

Transmission method

Ethernet Type II

 

Transmission cable

Category 5e, 100m (Max)

Transmission speed

10/100 Mbps Auto-Detection

Network protocol

ICMP, IP, TCP, UDP, DHCP, SMTP, MODBUS OVER TCP/IP, Delta

Configuration

9

 

 

 

Unit: mm

￿Address Switch

Switch setting

Content

01 … F7

Valid Modbus communication address

￿Data Format Switch

Switch setting

Format

Switch setting

Format

0

7-N-1

8

7-N-2

1

8-N-1

9

8-N-2

2

7-O-1

A

7-O-2

3

8-O-1

B

8-O-2

6

7-E-1

E

7-E-2

7

8-E-1

F

8-E-2

￿Baud Rate Switch

Switch setting

Baud rate (bps)

Switch setting

Baud rate (bps)

1

110

7

4,800

2

150

8

9,600

3

300

9

19,200

4

600

A

38,400

5

1,200

B

57,600

6

2,400

C

115,200

￿Codes in Digital Display

Code

Indication

01 ~ F7

The node address of IFD9506 when

in normal operation

 

F0

Returning to default setting

F1

IFD9506 is booting

F2

Working power in low voltage

F3

Internal memory error

F4

Internal error caused by

manufacturing in the factory

 

F5

Network connection error

F6

Full number of devices connected in

the network

 

F7

UART setting error.

E1

Alarm 1 triggered

E2

Alarm 2 triggered

E3

Alarm 3 triggered

01Incorrect MODBUS function

02Incorrect address

03Incorrect data

04

CRC error

0B

No response from the station

How to correct

--

--

--

Check if the working power is normal.

1.Re-power IFD9506. If the error still exists, try step 2.

2.Reset IFD9506. If the error still exists, send it back to the factory for repair.

1.Re-power IFD9506. If the error still exists, try step 2.

2.Reset IFD9506. If the error still exists, send it back to the factory for repair.

Check if IFD9506 is normally connected to the network.

Check if the number is too much.

Check if the RS-485, RS-232 communication format is correct.

Check Alarm Input Point 1.

Check Alarm Input Point 2.

Check Alarm Input Point 3.

Check if the Modbus instruction is correct.

Check if the Modbus instruction is correct.

Check if the Modbus instruction is correct.

1.Check if IFD9506 and RS-485 is connected normally.

2.Check if the series transmission speed is consistent with that of other nodes on the network.

1.Check if IFD9506 and RS-485 is connected normally.

2.Check if the series transmission speed is consistent with that of other nodes on the network.

 

端子台連接器

10PIN

 

 

 

 

 

 

 

 

RS-485

 

 

 

 

 

 

 

 

 

1,200m

 

 

 

 

 

 

 

 

 

110, 150, 300, 600, 1,200, 2,400, 4,800, 9,600, 19,200, 38,400, 57,600, 115,200

 

 

 

 

 

Stop bit: 1,2

Parity bit: None, Odd, Even Data bit: 7,8

ASCII/RTU

 

 

 

 

 

Modbus, User Define

 

 

 

￿

 

 

 

 

 

 

 

 

 

 

電氣規格

24V DC (-15% ~ 20%)

 

 

 

 

接頭

方

 

 

3W

 

 

 

 

 

 

 

500V

 

 

 

 

 

 

 

140g

 

 

 

 

 

 

 

 

 

 

 

 

 

￿

 

速率

 

 

 

 

 

 

 

 

格式

 

ESD (IEC 61131-2, IEC 61000-4-2): 8KV Air Discharge

 

 

通訊協定

 

EFT (IEC 61131-2, IEC 61000-4-4): Power Line:±2KV, Digital Input: ±2KV,

 

 

電纜

 

Communication I/O: ±2KV

 

 

 

環境

 

 

RS (IEC 61131-2, IEC 61000-4-3): 80MHz ~ 1GHz, 10V/m. 1.4GHz ~ 2.0GHz, 10V/m

 

接頭

 

 

 

Conducted Susceptibility Test (EN61000-4-6, IEC61131-2 9.10): 150KHz ~ 80MHz,

 

 

 

 

3V/m

 

 

 

 

 

方

 

 

歐式端子台

 

 

 

 

 

 

 

 

Surge Test (Biwave IEC61132-2, IEC61000-4-5):

 

 

 

 

 

Power line 0.5KV DM, Ethernet 0.5KV CM, RS-485 0.5KV CM

 

 

距離

 

0ºC ~ 55ºC

50 ~ 95%

2

 

傳輸速率

 

操作：

 

 

5 ~ 95%

 

 

 

-25ºC ~ 70ºC

 

 

 

 

格式

/

國際標準規範

IEC61131-2, IEC68-2-6 (TEST Fc)/IEC61131-2 & IEC 68-2-27(TEST

 

通訊協定

 

由歐式端子台輸入

 

 

 

Ea)

 

 

 

源

 

力

 

 

 

 

 

消耗

 

 

 

 

 

 

 

 

絕緣電壓

 

儲存

（溫度）、（溫度）、

（濕度）、污染等級（濕度）

 

 

標耐操雜重準震作訊量動∕免∕儲疫存環境力衝擊

 

Page 1 Page 2
Page 1
Image 1
Delta Electronics IFD9506 specifications 產品外觀 通訊口, 產品簡介 功能特色 傳輸速率， 自動偵測。, 按鍵、, 端子台, 電源指, 站號設定開關, 指示燈、, 模組名稱 指示燈, 網路協定 傳輸速率
Page 1 Page 2

IFD9506 specifications

Delta Electronics has long been a leader in power management solutions, and the IFD9506 is a testament to their commitment to innovation and efficiency. The IFD9506 is an advanced Integrated Fan Drive (IFD) designed for optimal performance in various applications, particularly in HVAC systems and industrial processes. This intelligent fan drive combines cutting-edge technologies to enhance energy efficiency, reliability, and control.

One of the main features of the IFD9506 is its variable frequency drive (VFD) capability, which allows for precise control of motor speed and torque. This results in significant energy savings, as motors can operate only at the required speed for a specific application, minimizing wastage. The drive is capable of controlling both AC induction motors and permanent magnet synchronous motors, making it versatile for different deployment scenarios.

The IFD9506 also integrates advanced control algorithms, including vector control and sensorless control, which optimize the performance of the motor. These technologies improve torque response and efficiency across varying load conditions. Users can expect enhanced performance in terms of acceleration and deceleration, leading to smoother operations and less wear on mechanical components.

Another standout characteristic of the IFD9506 is its communication capabilities. It supports various industrial communication protocols, such as Modbus, Ethernet/IP, and CANopen. This allows the drive to seamlessly integrate into smart building or industrial automation systems, enabling real-time data exchange and remote monitoring. The integration of such protocols supports condition-based maintenance, reducing downtime and service costs.

In terms of user interface, the IFD9506 is designed with an intuitive control panel that simplifies setup and operation. The full-text LCD display provides clear status feedback, while programming can be easily completed through the menu-driven interface. Additionally, the drive comes with built-in protection features against overvoltage, overcurrent, and short circuits, ensuring reliable operation even in demanding environments.

The IFD9506 is also engineered with a robust thermal management system, allowing it to function effectively in high-temperature settings. Its compact design makes it easy to install in constrained spaces, while the durable construction ensures longevity and performance under varying conditions.

In conclusion, Delta Electronics' IFD9506 is a powerful and efficient integrated fan drive that enhances motor performance while providing significant energy savings. With its advanced features, communication flexibility, and user-friendly design, it represents a significant advancement in power management technology, making it an ideal choice for both commercial and industrial applications.
Top Page Image Contents