GAudioH
Symptom | Cause/Solution | Page |
Audio is not output. | • Check the connections for all devices. | C 4, |
|
| 5, 7, 8, |
| • Check the speaker connections and configurations. | 9, 10 |
| C 3, | |
| • Check whether the audio device power is turned on. | 24, 25 |
| – | |
| • Adjust the master volume. | 11 |
| • Cancel the mute mode. | 11 |
| • Select a suitable input source. | 11 |
| • Select a suitable input mode. | 32 |
| • Disconnect the headphones. No sound is output from the speakers | 42 |
| or the PRE OUT connectors when headphones are connected. |
|
No sound is | • Check if the surround speakers are connected to the SURROUND | – |
produced from | terminals. |
|
surround speaker. |
|
|
No sound is | • Set “Speaker Config.” – “Surround Back” on the menu to | C 6 |
produced from | something other than “None”. |
|
surround back | • Set the surround mode to something other than “STEREO”. | 19 |
speaker. |
|
|
No sound is | • Check the subwoofer connections. | C 3, |
produced from |
| 24, 25 |
subwoofer. | • Turn on the subwoofer’s power. | C 4 |
| • Set “Speaker Config.” – “Subwoofer” on the menu to “Yes”. | C 6 |
| • If “Front” and “Center” for “Speaker Config.” are set to “Large”, | C 5, |
| and “SW Mode” is set to “LFE”, no sound may be output from | C 6 |
| the subwoofers, depending on the input signal or selected |
|
| surround mode. |
|
DTS sound is not | • Set “Decode Mode” on the menu to “Auto” or “DTS”. | 32 |
output. |
|
|
Dolby TrueHD, DTS- | • Make HDMI connections. | 5 |
HD, Dolby Digital |
|
|
Plus audio is not |
|
|
output. |
|
|
Dolby PLg mode or | • Check that “Speaker Config.” – “Center” or “Surround” is set | C 5 |
DTS NEO:6 mode | to other than “None”. If the speaker system is 2.0/2.1ch, this |
|
cannot be selected. | surround mode cannot be selected. |
|
| • When headphones are used, Dolby PLg or DTS NEO:6 cannot be | – |
| selected. |
|
RESTORER cannot | • Check that an analog signal or PCM signal (fs=44.1/48 kHz) is | 39 |
be selected. | input. For playback of multichannel signals such as Dolby Digital |
|
| or DTS surround, RESTORER cannot be used. |
|
GRadioH
Symptom | Cause/Solution | Page | |
Reception fails, or |
| • Change the antenna orientation or position. | 10 |
there is a lot of noise |
| • Separate the AM loop antenna from the unit. | 10 |
or distortion. |
| • Use an FM outdoor antenna. | 10 |
|
| • Separate the antenna from other connection cables. | 10 |
GControl dock for iPodH |
| ||
Symptom | Cause/Solution | Page | |
iPod cannot be |
| • Check the iPod connections. | 9 |
played. |
| • Insert the AC adaptor of the iPod control dock into the power | – |
|
| outlet. |
|
|
| • Switch the input source to “DOCK”. | 11 |
“Connection Error” |
| • Unable to communicate properly. Turn off the power to this unit, | – |
is displayed. |
| disconnect the iPod and then reconnect it. |
|
|
| • The iPod is not responding. Turn off the power to this unit, | – |
|
| disconnect the iPod and then reconnect it. |
|
“Not Support” is |
| • The iPod connected to the unit is not compatible. Please make | – |
displayed. |
| sure the iPod you are connecting is compatible. |
|
|
| • The software version of the connected iPod is an old one. Please | – |
|
| update to the latest version. |
|
GRemote Control UnitH |
|
| |
Symptom | Cause/Solution | Page | |
The set cannot be |
| • Batteries are worn out. Replace with new batteries. | 46 |
operated with the |
| • Operate the remote control unit within a distance of about | 46 |
remote control unit. |
| 23 ft/7 m from this unit and at an angle of within 30°. |
|
|
| • Remove any obstacle between this unit and the remote control | 46 |
|
| unit. |
|
|
| • Insert the batteries in the proper direction, checking the q and | 46 |
|
| w marks. |
|
|
| • The set’s remote control sensor is exposed to strong light (direct | 46 |
|
| sunlight, inverter type fluorescent bulb light, etc.). Move the set |
|
|
| to a place in which the remote control sensor will not be exposed |
|
|
| to strong light. |
|
version Basic
version Advanced
Information
56