Denon AVR-2802 manual 22

1 Simulcast playback

Use this switch to monitor a video source other

than the audio source.

VIDEO SELECT

Press the VIDEO SELECT

button repeatedly until the desired source appears on

the display.

(Main unit)

ENGLISH

After starting playback

[1]Adjusting the sound quality (TONE)

The tone control function will not work in the Direct mode.

1	The tone switches as follows each time the
	TONE CONTROL button is pressed.			B
	TONE
	CONTROL
	BASS	TREBLE
	(Main unit)
2				3	2 1
	With the name of the volume to		SELECT
	be adjusted selected, turn the
	SELECT knob to adjust the level.
			(Main unit)
	• To increase the bass or treble: Turn the control 3			If you do not want the bass and treble to be
				adjusted, turn on the tone defeat mode.
	clockwise. (The bass or treble sound can be
	increased to up to +12 dB in steps of 2 dB.)			TONE DEFEAT
				The signals	do not pass
	• To decrease the bass or	treble: Turn the
				through the bass and treble
	control counterclockwise. (The bass or treble			adjustment circuits, providing
	sound can be decreased to up to –12 dB in			higher quality sound.
	steps of 2 dB.)			(Main unit)
[2]	Listening over headphones
1	Connect the headphones to		PHONES
	the PHONES jack of the front			B

panel.

1

[4] Combining the currently playing sound with the desired image

B

Cancelling simulcast playback.	1
• Select “SOURCE” using the	VIDEO
SELECT button.
• Switch the program source	to the

component connected to the video input.

[5] Checking the currently playing program source, etc.

1

On screen display

ON SCREEN

• Each time

an operation

is

RETURN

performed,

a description

of

SYSTEM

SURROUND

that operation appears

on

TUNING

SETUP

PARAMETER

BAND

RDS

TITLE

MENU/GUIDE

the display connected to the (Remote control unit)

CH SELECT

MODE

PTY

ENTER

SELECT

1

unit’s VIDEO MONITOR OUT

MEMORY

RT

STATUS

ON SCREEN

DISPLAY

RETURN

jack.

USE/LEARN T.TONE

MULTI

DVD

1

SET UP

Also, the unit’s operating status can be

checked during playback by pressing the

1

remote control unit’s ON SCREEN button.

Such information as the position of the input

Using the dimmer function

selector and the surround parameter settings

DIMMER

• Use this to change the brightness of

is output in sequence.

the display.

Front panel display

The display

brightness changes

in

• Descriptions of the unit’s operations are also

four steps (bright, medium, dim and

(Main unit)

displayed on the front panel display.

off) by pressing the remote control

In addition, the display can be switched to

unit’s DIMMER button repeatedly.

check

the

unit’s

operating

status while

The brightness changes in 3 steps each time the

playing

a source

by pressing

the STATUS

button is pressed, and finally the display turns off.

button.

2 Pressoff. the SPEAKER A or B to turn the speaker

(Main unit)

•The output to the speaker and pre-out jacks is turned off and no sound is produced from the speakers.

[3]Turning the sound off temporarily (MUTING)

1 2

NOTE:

To prevent hearing loss, do not raise the volume level excessively when using headphones.

STATUS	STATUS
	DISPLAY
(Main unit)	(Remote control unit)

1	Use this to turn off the audio	MUTING
	output temporarily.			DOLBY / DTS	STEREO
			DSP SIMULATION 5CH / 6CH STEREO
			SPEAKER	SURROUND	DIRECT
	Press the MUTING button.		INPUT MODE	ANALOG	EXT.IN	MASTER VOL.
	Cancelling MUTING	(Remote control unit)	AVR/AVC	VIDEO DVD	TV		1
			AUDIO	TAPE CDR/MD
	mode.			CD	MULTI	MUTING
				VDP VCR
	Press the MUTING button again.

22