Denon AVR-2802 21

3	Select the play mode.
3	Press the SURROUND MODE button, then turn
	the SELECT knob.

Input mode display

		One of these lights, depending on
• In the AUTO mode		the input signal.
• In the AUTO mode
	INPUT

ENGLISH

Playback using the external input (EXT. IN) jacks

Example: Stereo
SURROUND	SELECT
MODE	STEREO

(Main unit)(Remote control unit)

	To select the surround mode				SURROUND
	while	adjusting	the surround		MODE
	while	adjusting	the surround
	parameters, channel volume or
	tone	control,	press	the
	surround mode		button	then	(Main unit)
	operate the selector.
4	Start playback on the selected component.
4	• For operating instructions, refer to the
	component’s manual.
5	Adjust the volume.
			MASTER VOLUME

MASTER VOL.

The volume level is

displayed on the(Main unit) (Remote control unit) master volume level

display.

The volume can be adjusted within the range of

–70 to 0 to 18 dB, in steps of 1 dB. However, when the channel level is set as described on page 12 or page 24, if the volume for any channel is set at +1 dB or greater, the volume cannot be adjusted up to 18 dB. (In this case the maximum volume adjustment range is “18 dB — (Maximum value of channel level)”.)

Input mode when playing DTS sources

•Noise will be output if DTS-compatible CDs or LDs are played in the “ANALOG” or “PCM” mode. When playing DTS-compatible sources, be sure to connect the source component to the digital input jacks (OPTICAL/COAXIAL) and set the input mode to “DTS”.

AUTO	PCM	DTS	DIGITAL ANALOG
			DIGITAL ANALOG

•In the DIGITAL PCM mode

	INPUT
AUTO	PCM	DTS	DIGITAL
			DIGITAL

•In the DIGITAL DTS mode

	INPUT		DIGITAL
AUTO	PCM	DTS	DIGITAL

•In the ANALOG mode

	INPUT
AUTO	PCM	DTS	ANALOG

Input signal display

•DOLBY DIGITAL

SIGNAL

DIGITAL

•DTS

SIGNAL

DIGITAL

•PCM

SIGNAL

DIGITAL

The DIGITAL indicator lights when digital signals

are being input properly. If the DIGITAL indicator

does not light, check whether the digital input component setup (page 13) and connections are correct and whether the component’s power is turned on.

NOTE:

•The DIGITAL indicator will light when playing CD-ROMs containing data other than audio signals, but no sound will be heard.

1	Set the external input (EXT. IN) mode.
	Press the EXT. IN to switch the external input.
	EXT.IN	EXT.IN

	(Main unit)	(Remote control unit)
	Once this is selected, the input signals
	connected to the FL (front left), FR (front right),
	C (center), SL (surround left) and SR (surround
	right) channels of the EXT. IN jacks are output
	directly to the front (left and right), center and
	surround (left and right) speaker systems as
	well as the pre-out jacks without passing
	through the surround circuitry.
	In addition, the signal input to the SW
	(subwoofer) jack is output to the PRE OUT
	SUBWOOFER jack.
2	Cancelling the external input mode
	To cancel the external input (EXT. IN) setting,
	press the input mode (AUTO, PCM, DTS) or
	ANALOG button to switch to the desired input
	mode. (See page 20.)
	INPUT MODE ANALOG	INPUT MODE	ANALOG

	(Main unit)	(Remote control unit)

•When the input mode is set to the external input (EXT. IN), the play mode (DIRECT, STEREO, DOLBY/DTS SURROUND, 5/6CH STEREO or DSP SIMULATION) cannot be set.

	2	1
	VOLUME				DISC SKIP+
		DOLBY / DTS
	SPEAKER	SURROUND		DIRECT
	DSP SIMULATION	5CH / 6CH STEREO STEREO
					MASTER VOL.
2	INPUT MODE	ANALOG		EXT.IN		1
2	AUDIO		TAPE	CDR/MD		1
	AUDIO		CD	MULTI	MUTING
	AVR/AVC	VIDEO	DVD	TV
			VDP	VCR
			SYSTEM		SURROUND
	TUNING		SETUP		PARAMETER
	BAND	RDS	TITLE		MENU/GUIDE
	BAND	RDS
				CH SELECT
	MODE	PTY		ENTER
				SELECT

NOTES:

•In play modes other than the external input mode, the signals connected to these jacks cannot be played. In addition, signals cannot be output from channels not connected to the input jacks.

•The external input mode can be set for any input source. To watch video while listening to sound, select the input source to which the video signal is connected, then set this mode.