Denon AVR-2802 manual 19

(3) Storing signals						(4) Clearing system call settings
		START	LEARNED/TX		RC-904			START	LEARNED/TX		RC-904
1,5						1,3
	SYSTEM CALL			POWER			SYSTEM CALL			POWER
	SET	CALL	OFF		/		SET	CALL	OFF		/
	DVD	VDP		TUNER	SHIFT		DVD	VDP		TUNER	SHIFT
	1	2		3			1	2		3
2	TV/DBS			PHONO		2	TV/DBS			PHONO
	4	5		6			4	5		6
	VCR-1	CD		CDR / TAPE	CHANNEL		VCR-1	CD	CDR / TAPE		CHANNEL
	7	8		9			7	8		9
	VCR-2/V.AUX				TV/VCR		VCR-2/V.AUX				TV/VCR
	+10	0			A / B		+10	0			A / B
	VOLUME				DISC SKIP+		VOLUME				DISC SKIP+
		DOLBY / DTS						DOLBY / DTS
	SPEAKER	SURROUND		DIRECT			SPEAKER	SURROUND		DIRECT
	DSP SIMULATION	5CH / 6CH STEREO		STEREO			DSP SIMULATION	5CH / 6CH STEREO STEREO
					MASTER VOL.						MASTER VOL.
	INPUT MODE	ANALOG		EXT.IN			INPUT MODE	ANALOG		EXT.IN
3	AUDIO		TAPE	CDR/MD			AUDIO		TAPE	CDR/MD
		CD		MULTI	MUTING			CD		MULTI	MUTING
	AVR/AVC	VIDEO DVD VDP		VCR TV			AVR/AVC	VIDEO DVD VDP		VCR TV
			SYSTEM		SURROUND				SYSTEM		SURROUND
	TUNING		SETUP		PARAMETER		TUNING		SETUP		PARAMETER
	BAND	RDS	TITLE		MENU/GUIDE		BAND	RDS	TITLE		MENU/GUIDE
				CH SELECT						CH SELECT
	MODE	PTY		ENTER			MODE	PTY		ENTER
				SELECT						SELECT
	MEMORY	RT	STATUS		ON SCREEN		MEMORY	RT	STATUS		ON SCREEN
		DISPLAY			RETURN			DISPLAY			RETURN
	USE/LEARN	T.TONE	MULTI		DVD		USE/LEARN	T.TONE	MULTI		DVD
					SET UP						SET UP

Clearing “learned” remote control signals

1	Press the USE/LEARN selector button with the
	tip of a pen, etc., to set the learn mode.

2	To clear “learned” remote control signals, set
	the slide switch to the position at which the

signals were “learned”.

AUDIO

AVR/AVC VIDEO

ENGLISH

		START	LEARNED/TX		RC-904
4
	SYSTEM CALL			POWER
	SET	CALL	OFF		/
	DVD	VDP		TUNER	SHIFT
	1	2		3
	TV/DBS			PHONO
	4	5		6
	VCR-1	CD		CDR / TAPE	CHANNEL
	7	8		9
	VCR-2/V.AUX				TV/VCR
	+10	0			A / B
	VOLUME				DISC SKIP+
		DOLBY / DTS
	SPEAKER	SURROUND		DIRECT
	DSP SIMULATION	5CH / 6CH STEREO		STEREO
					MASTER VOL.
	INPUT MODE	ANALOG		EXT.IN
2	AUDIO		TAPE	CDR/MD
		CD		MULTI	MUTING
	AVR/AVC	VIDEO DVD		TV		3
			VDP	VCR
			SYSTEM		SURROUND
	TUNING		SETUP		PARAMETER
	BAND	RDS	TITLE		MENU/GUIDE
				CH SELECT
	MODE	PTY		ENTER
				SELECT
	MEMORY	RT	STATUS		ON SCREEN
1,5		DISPLAY			RETURN
	USE/LEARN	T.TONE	MULTI		DVD
					SET UP

1	Press the SET button.	1	Press the SET button.
	• The START LED and LEARNED/TX LED both
	flash.		SET

SET

3	Set the slide switch to the position at which the
	signals were “learned”.
		TAPE	CDR/MD
	CD			MULTI
		DVD		TV
		VDP	VCR

2	Press the button at which you want to store the
	system call signals.
	• The START LED flashes.
3	Set the mode switch to the position for the
	component whose remote control signals you
	want to store.

		TAPE	CDR/MD
AUDIO		CD	MULTI
AVR/AVC	VIDEO	DVD	TV
		VDP	VCR

4	Press the buttons whose remote control
	signals you want to store one by one.
5	Press the SET button.
	SET

2	clear.Press the button whose settings you want to
3	Press the SET button.

• The button is reset to the settings shown on the table on page 18.

SET

4	Press the SYSTEM CALL SET button, and hold
	it in for at least four seconds.

•When both the START and LEARNED/TX LEDs light simultaneously, all the stored codes are cleared.

Light

	SET
5	Press the USE/LEARN selector button.

NOTES:

•The remote control signals for the buttons pressed while storing the system call signals are transmitted when the buttons are pressed, so cover the remote sensor or take other measures so that the components do not operate while the signals are being stored.

•The LEARNED/TX LED does not light if system call signals cannot be stored at the button that you have pressed or if you have already stored the maximum number of signals.

19