Denon DN-C680 manual Auto CUE button

AUTO CUE button

•Press this button to find the beginning of the playback signals on a track and automatically set the standby mode at that point. (Auto

Cue)

•The button lights when the auto cue mode is set.

•Press the button again to cancel the auto cue mode.

AUTO SPACE button

•Press this button to automatically insert blank spaces of 4 seconds between tracks during continuous playback. (Auto Space)

•The button lights when the auto space mode is set.

•Press the button again to cancel the auto cue mode.

AUTO EDIT button

•Press this button to divide the tracks on the disc into a first half (side A) and second half (side B) at the point nearest to half of the disc's total playing time. (Auto Edit)

•When the A button is pressed while the auto edit mode is on, the A button lights and the number of the first track and total playing time of the first half (side A) are displayed on the character display.

•When the B button is pressed while the auto edit mode is on, the B button lights and the number of the first track and total playing time of the second half (side B) are displayed on the character display.

•Press the button again to cancel the auto edit mode.

TIME button

•Press this button to switch the time display between the remaining time (REMAIN) and the elapsed time (ELAPSED).

INDEX button

•Press this button to set the index select mode, then use the select knob to select the index number.

•The button lights when the index select mode is set.

•Press the button again to return to the track select mode.

FADER button

•Press this button to enable input of the fader input signals connected to the "PARALLEL REMOTE" connector.

•The button lights when fader input signal input is enabled.

•Press the button again to cancel the mode.

FINISH MODE button

One of the following three finish modes can be selected:

•Press the STOP button to light the button and set the finish mode to the stop mode.

•Press the NEXT button to light the button and set the finish mode to the next mode.

•Press the RECUE button to light the button and set the finish mode to the recue mode.

SEARCH dial (inner side)

•Turn this dial to set the manual search mode.

•Turn the dial clockwise to move the playback position forward, counterclockwise to move the playback position backward.

•One click corresponds to one frame of movement. The playback position can be moved anywhere between the beginning of the first track and the end of the last track.

SCAN dial (outer side)

•Turn this dial to set the manual search (fast forward or fast reverse) mode.

•Turn the dial clockwise to move the playback position forward, counterclockwise to move the playback position backward.

•The speed changes according to the angle at which the dialis turned.

Rear Panel

DIGITAL OUT (BALANCED) connector

•This is an active balanced output using an XLR type connector.

•Connect this connector to the balanced digital input connector on an amplifier or console.

•Signal format: Selectable (See Page 24, 8) 9))

• Pin layout:	1. Common
	2.	Cold
	3.	Hot

•Applicable connector: Cannon XLR-3-31 or equivalent

DIGITAL OUT (UNBALANCED) jack

•This is an unbalanced output using an RCA type jack.

•Connect this jack to the unbalanced digital input jack on an amplifier or console.

•Signal format: Selectable (See Page 24, 8) 9))

ANALOG OUT (BALANCE) connectors

•These are active balanced outputs using XLR type connectors.

•Connect these connectors to the balanced analog input connectors on an amplifier or console.

•Pin layout:

Pin No.	U.S.A. & Canada	Europe & Asia & Others
1	Common	Common
2	Cold	Hot
3	Hot	Cold

•Applicable connector: Cannon XLR-3-31 or equivalent

NOTE: Do not short-circuit the hot or cold pin with the common pin.

LEVEL L/R controls

•Use these controls to adjust the level of the audio-signals from the ANALOG OUT (BALANCED) connectors.

ANALOG OUT (UNBALANCED) jacks

•These are unbalanced outputs using RCA type jacks.

•Connect these jacks to the unbalanced analog input jacks on an amplifier or console.

10